Clutch went but compessor is fine. I looked for a new mopar clutch but they are real expensive like 300 bucks and only dealers sell them???? so I decided to get a new or reman compressor as i can get one of those for about 200.
I know when a compessor blows you need to replace the...
Here is a really cool link I found on installing an ARB in a dana 44.
I posted this under the front or rear locking thread but I thought it would be good to repost it for all. I think I may throw it up on LOST too.
If you wondered what was involved and about a do it yourselfer this may...
When I did my lift I threw in a 3 ring clevis and I had an 1/8'' of clearence at full drop. I did some fender mods today and I notice at full drop I have contact. Sucks. Guess she settled in a little or something.
Think they will last a little while but as soon as I get a hole I am going to...
Pardon the pun up there!!LOL
I was just wondering cause I noticed the 8.25 takes 75w-90 agl 5 gear oil and the other three diffs for libbies take 75w-140 synthetic.
plus the friction mod for a limited slip
Anyone know why??
Looked in how to and couldn't find any info on this.
I went to 245/75 16's, M/T rs and I am getting a little rubbing on the front wheel wells next to the foglamp doors
My question is cut or heat and reform?
I know I can get out the dremel and be rub free in about 3 minutes but I was...
I was looking at jeep.com trying to find what my axle is. I think its 3.92 but i found this picture of a KJ and its jacked up with tires that are definetly not 235 70's
Thought it was funny DC would have this on the offical website. Here is the link check it out.
It won't take you...
I heard that Frankenlift uses spacers. Anyone ever add spacers to a rusty's?
I assume with a frankenlift you have to get an allJ upper arm or you will wack your balljoints.
I have also heard of some Frankenlift folks tearing up their CV boots as well.
Just curious.
Hi folks,
I was gonna put some 15x8 cragers on with some 31x10.5 bfg k/o but when I test fit the rims I had less that an 1/8'' of clearence from the calipers. Too close for me. Plus I chickened out on the fender mods I would have for the 31's cause of how wide they are and the backspace I...
Hi Guys and Gals,
I have been looking around at brush/bull bars. What type do you like? Good or bad experiences? I was looking at a ARB but the expenses and weight are a concern for me. I didn't get the HD coil for my lift.
What is the best bang for my buck in a bull/brush bar?
Which...
To anyone who has the rro sliders. Did you have a hard time with the front bolt mounts? Where mine are sitting I can't get the fronts bolted. The weld form on the U-channel is in the way. I think my sliders may be for a 05-06 not for my 03. I snapped a 5/16'' drill bit trying #-o :-# . Even if...
When I installed my front stuts I didn't have any one to help manuvere it in and as a result I got some pretty good scratches through the powder coat.
I was wondering if I should bother sealing this or should I forget about it.
If I need to seal it what should I use other than rustoleum...
welding edges of the flipper gate edges? It looks like the welds have sprung open and water is getting into it.
Wonder how much this is going to cost me. ](*,)
I am getting a lift from rusty's and I thinking about putting some p245 75 16's on the renny and I was wondering if I will notice any torque loss?
Also will I need to pound the pinch weld?
Thanks!!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.