Search results

My 2005 Liberty suspension is getting crusty. The wife is getting old and the rough ride hurting her. I only have 140 on it. Needs ball joints, 1 front wheel bearing, 2 front tires, 1 front brake hose, wheel alignment, ****** pan and ****** lines, radiator . Clearcoat peeling and needs shampoo...

I did not put on the new axle shaft

LF like a knobby tire, assumed wheel bearing, ordered new. bought 35mm soc., and 6pt set., got 35mm nut off, could not budge 6pt bolts, realized wrong new hub and sent back and gave up months ago. Started in again last wk, got used knuckle/hub from NC not crusty, broke it all down and...

I also had a left front noise, growling. I got a used knuckle with hub in it from NC as less rust, Mine was so crusty I could not bust the hub bolts loose. Changed it and I still have the growl but a little different ? Maybe CV joint or the used bearing is also NG. Try A1A auto for parts. It...

Posting a link as this forum wouldn't take pics (to big ) but my hot rod site did . Thanks for any input.https://www.hotrodders.com/forum/ot-daily-driver-hub-rust-515703.html#post4604329

Replaced my post O2 sensor bank 1 and check engine light went away after a few days and has not come back . I have 3 more if I need them NTK's

So I am gettung around to posting results. Could not be happier. Lamps snap into place after removing all the hardware that comes on then. Put small screws back into threaded vholes on side of lamp and force into plastic holes on car. It will require some persuasion but once in no need to...

I returned and got a new set. Hope to try them out tomorrow. So I got them in and wired up, However I need to find a +12VDC under the hood preferably, that is only on when key is on/car running to provide for DRL feature. Thanks ,Bob.

Not today but saturday last new front rotors and pads. Wagner. Just for hahas googled video and found that jack bolts instead of BFH will get old rotor off. As I am in a RV park where they frown on repair work I did not want to make much noise. Google Search is a great friend. I had to rest up...

I had a rough idle and trouble starting and they found a bad injector. There was water around it they said. They replaced it . There was noe check engine light. That was at around 50K and now have 93K same plugs . I think its time I put in new plugs and injector packs ?

I am having trouble getting these to work. I have set up using the ballast box just like the video and cannot get the turn or hazes to work. The booklet calls for another wire to be connected along with the yellow (found out that the blue ignition+ wire needs to be hot when testing in order for...

Not for nuthin' but you said you took it in because of coolant loss and they said new radiator. Did they look at the car first ? Did they show you where it was leaking. Usually you can SMELL antifreeze when there is a external leak. Also, like has been said , if the cooling systwm has not been...

I have recieved my fog lamps/DRL . Rainy and cold , so have to wait to install. I will not be using the PS as I only need fog. However , I do want to feed the DRL wire so they come on when the engine is running.Where is the best place to wire that in ? Anyone know ? Thanks, Bob.

Thanks for the info. . I like the fact that it will do daytime. I can wire etc.

Mine do not look so new anymore. They do not seem to be made of the same material as the headlight lens. Replace bulbs last year for better but not what I wanted. Any suggestions for complete housing with brighter bulbs. MA resident. I also want them to come on with key in on position to use...

new water pump

DD water pump needs replacing. Have a new one from mopar along with hoses . I see on all the vid's to torque the bolts down. My torquq wrench is not here yet and the day is great for working outside and would like to get started. Never did an aluminum WP before but I know enough not to over...