The top of the new shocks doesnt have a sleeve . Only a bushing and there is to much space between the frame mounting point. I measure just under 2in from the old shock sleeve. And the bottom eye sockets i was thinking of adding a few washers to get a snugg fit between the sides as there is...
Hello was wondering how to get the bushings for rear shocks 24-185660? Do i need to take them to a shop to have them taken out and pressed .im currently doing my rear lift. Thanks
I guess when i bought the front mounting strut plates it said bearings included which i think they meant the bushing thats intact with the mounts. So i think i should be good then?. I supplied all four isolators for bottom and top coil springs. And what ever hardware that was included with the...
Hello i would like to know which way are the two small peices of hardware should be facing while assembling the coil over set. I took everything to a shop and want to make sure its done correctly. Should the two pieces be hugging the strut bearing or should the lower washer be facing down in...
It worked! I got some of that Free all spray and let it soak in. Then wedged the bushing sleeve and sprayed some more inside and gave it another try and the bolt slid right off. Thanks again for all the advice . After two days of smacking it and cursing . My neighbors probably thought i was crazy!
Ok i will try the drill as i can get the sleeve and fit a flat head in between the sleeve opening . I torched the rubber bushing off so the control arm is loose. Im still trying to see if the penetrating fluid will go in between. I will let you know how it goes today. Thank you
That’s exactly what i been doing. The nut turns but very snugg as i move the UCA up and down and hold it . I have about 1/2 in left before it goes through the first hole of the bolt . Im trying some penetrating oil and let it soak in longer then i will continue how you did it. No luck with the a...
Im trying to remove the right passenger UCA and one of the bearings on the bushing has seized on the bolt. I cant remove it . I tried smacking the bolt out at least 100 times already. Its almost out but how am i suppose to loosen the rest of it. I cant get a dremel in there . Should i use a...
So i had the issue with no start no click and discovered a piece that chipped off on the pin. Couldn't find the piece but still messed with the switch and was able to turn on the engine with a flat head and fired right up. I will need a new actuator i ordered (Dorman brand) . As you can see in...
Hello , So i had an issue this week with the p0139. The stubborn 02 sensor was giving me problems. Scanned and reset twice. I drove on the fwy the second time with my scanner to make sure it wasn't pending. I then drove it to get smogged and it passed luckily. On top of that i have another...
I only jacked up about two inches up . I though since i have saggy springs that was the reason it was less. .but i was able to only get 1 3/4 also. Drove it today felt good.
Does the front differential still spin even if its not in 4x4 ?
Im trying to read around some mixed reviews . Thanks
Hello so I changed my front differential fluid today.
I was only able to get about a little under 2quarts until it started dripping out the filler plug. I even jacked up the passenger side to help put in more .
Is this enough?
Thanks
04 liberty auto/with command trac.
I would like to share a little advice for california emission cats. I live in so cal and I called a few local muffler shops and found one shop that cut off and welded a new cat for me . (Drivers side) only the catalytic converter not the whole Pipe.Took one day for them to get the cat and do it...
Hello was wondering if anyone could help with finding the correct Bump stops for Rear? Im getting ready to do the OME 948 set up for the rear. Do i use the factory ones and just add the “hockey puck”at the bottom? Any part numbers would help . Thanks
Hello i wanted to know . Do i need new upper strut mounts if i am planning to do the ome lift set up. Could i use the old ones or can i go with some aftermarket mounts like moog? Thanks
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.