HOW TO: Change your front/rear diff oils

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

theroofable

Full Access Member
Joined
Oct 19, 2010
Messages
377
Reaction score
4
Location
NJ
As tjkj2002 explains in one of his posts on this thread the diffs are not pressurized systems and therefore the lubricant isn't forced into all areas of the differential - it is a "splash" system. The synthetic oils don't stay on the gears throughout the rotation as well as thicker 'dino' oils do - so going with a synth really isn't as good for your system as an 85W-140 dino oil.

You're spending money on a synthetic oil that doesn't do as good a job as a dino oil. Think of it this way: If it makes you feel better you could buy a gallon of 85W-140 for half the cost of a quart of full synth, change your diff oils twice as often and still save money! :party52:

Bob
Just verifying that I can use the 85w-140 in the front and the rear? If so Im off to buy 1 gal of it on tuesday, and hopefully get it changed before the weekend!
 

67Customs

Full Access Member
Joined
Sep 28, 2007
Messages
659
Reaction score
2
Location
North Carolina
As tjkj2002 explains in one of his posts on this thread the diffs are not pressurized systems and therefore the lubricant isn't forced into all areas of the differential - it is a "splash" system. The synthetic oils don't stay on the gears throughout the rotation as well as thicker 'dino' oils do - so going with a synth really isn't as good for your system as an 85W-140 dino oil.

You're spending money on a synthetic oil that doesn't do as good a job as a dino oil. Think of it this way: If it makes you feel better you could buy a gallon of 85W-140 for half the cost of a quart of full synth, change your diff oils twice as often and still save money! :party52:

Bob
I've read that a few times and I've done a lot of research on it.

However, that still doesn't explain to me why in my owners manual they specifically say to use 75W-140 in the front. They apparently thought it to be better at the time of that publication but thought 80W-90 to be good when writing the FSM.

Will my Dana 30a blow up because I use 85W-140? Probably not. I just want to know why they can't get it straight and if 75W-140 is better for my Dana 30a.

In all honesty, I'm most likely going to run Valvoline DuraBlend 85W-140 during my next change. Split the difference. But, she has already ran 60K miles on a couple of changes of Mobil 1 75W-140 front and back with zero problems.
 

TwoBobsKJ

Full Access Member
Joined
Jan 28, 2011
Messages
2,637
Reaction score
17
Location
Northern Ohio
I've read that a few times and I've done a lot of research on it.

However, that still doesn't explain to me why in my owners manual they specifically say to use 75W-140 in the front. They apparently thought it to be better at the time of that publication but thought 80W-90 to be good when writing the FSM.

Will my Dana 30a blow up because I use 85W-140? Probably not. I just want to know why they can't get it straight and if 75W-140 is better for my Dana 30a.

In all honesty, I'm most likely going to run Valvoline DuraBlend 85W-140 during my next change. Split the difference. But, she has already ran 60K miles on a couple of changes of Mobil 1 75W-140 front and back with zero problems.

In my opinion the Owner's Manual is as much marketing as information - and that's verified by the fact that the fluids referenced are always "Mopar-brand" so-and-so. With the 75W-140 Chrysler is pushing the more expensive product. But the FSM is for the mechanics who actually work on the vehicle and they are advised to use the stuff that will work well. In this case it is dino oil vs synth.

I think your choice is a good one (DuraBlend.) Gives you peace of mind and will do a good job in your diffs. :happy107:

Bob
 

Moon

Full Access Member
Joined
Jan 1, 2012
Messages
44
Reaction score
1
Location
Texas
I got the diff oil changed in the hooptie last friday. The only tip that I would mention (besides the ones already posted), is: DO NOT let the old gear-oil get into your car. It smells like so much nasty-ass, and doesn't seem to want to go away on its own. I had a rag with a little bit of the old oil on it. I threw it out the window while driving down the road, but the awful smell remains. :(

:cheers:
 

tjkj2002

Full Access Member
Joined
Dec 17, 2006
Messages
10,612
Reaction score
39
Location
Somewhere between being sane and insane!
I got the diff oil changed in the hooptie last friday. The only tip that I would mention (besides the ones already posted), is: DO NOT let the old gear-oil get into your car. It smells like so much nasty-ass, and doesn't seem to want to go away on its own. I had a rag with a little bit of the old oil on it. I threw it out the window while driving down the road, but the awful smell remains. :(

:cheers:
Try doing the front diff in a Cat 621B,55 gallons of 80w-90,that's one big drain pan.
 

first&lastKJ

Full Access Member
Joined
Oct 23, 2010
Messages
1,214
Reaction score
127
Location
Indiana
I have an 02 and 07 KJ does anyone know what gear lube came in them from the factory.
 

first&lastKJ

Full Access Member
Joined
Oct 23, 2010
Messages
1,214
Reaction score
127
Location
Indiana
Thanks. I think i'll go with the 75w-140 synthetic front and rear in both of our KJ's.
 
Last edited:

sevenhelmet

Full Access Member
Joined
Jul 16, 2007
Messages
649
Reaction score
1
Location
Ridgecrest, CA
I'm now using 80W-90 front and rear and I've put over 100 miles on it since the change with no problems.
 

mdmaroon

Full Access Member
Joined
Nov 27, 2011
Messages
31
Reaction score
0
Location
Richmond, BC, Canada
ahhh yes, been meaning to do a write up on this for a while now.

The rear has been pretty much covered. The only difference is I let the RTV cure on my cover for about 30 minutes and its held up great.

As for the front, this is really simple. There are two plugs, unlike the back. You have a drain plug, and a fill pulg. All you have to do is:

Unblot the drain plug.
let old oil drain out.
Put drain plug back on.
Unbolt fill plug.
Fill with new oil.
Put fill plug back on.

YOU'RE DONE!!! This is of course, if you DO NOT have any skid plates up front. I would imagine that skids up front would have to be taken off.

One thing: Take the fill plug out FIRST. If you take out the drain plug, and then for some reason can't get the fill plug out, then you aren't going anywhere until you do get it out, one way or another. Maybe you'll need a tow truck to take you to a shop...

I know it's not too likely that this will happen, but at least if you take the fill plug out first, you know you'll be able to get fluid in, assuming everything is okay with the drain plug. If you can't drain it, then you just put the fill plug back and you can still drive.
 
Last edited:

Squeeto

New Member
Joined
Jan 23, 2012
Messages
5
Reaction score
0
Location
Victoria, Canada
...
Someone was asking where to put the jack stands. Here is where I put them. I dont know if it is correct or not, but seems alright to me.
You must be registered for see images attach

I like this way as well. But it causes the diff to point up not hang down. If the oil level needs to be 1cm below the fill hole we aren't accomplishing this by filling until the oil drips out.

I figure that some fluid can be sucked out but how important is this oil level? It looks like the bottom of the axle (thus seals) is below the proper oil level anyway.

________

So I must jack the front to get under the truck for the front diff. If I let the axle hang it actually points down even if the front of the truck is elevated?


Sorry for being so cautious about this. This is the first vehicle I have owned that requires the level to be below the fill.
 

Squeeto

New Member
Joined
Jan 23, 2012
Messages
5
Reaction score
0
Location
Victoria, Canada
Okay, I tried this on the rear axle and it does work:

You must be registered for see images


String to diff cover:
level = 1 13/16 inch
hanging = 1 15/16 inch

I don't think that this trick works on the front though.
 

theroofable

Full Access Member
Joined
Oct 19, 2010
Messages
377
Reaction score
4
Location
NJ
I like this way as well. But it causes the diff to point up not hang down. If the oil level needs to be 1cm below the fill hole we aren't accomplishing this by filling until the oil drips out.

I figure that some fluid can be sucked out but how important is this oil level? It looks like the bottom of the axle (thus seals) is below the proper oil level anyway.

________

So I must jack the front to get under the truck for the front diff. If I let the axle hang it actually points down even if the front of the truck is elevated?


Sorry for being so cautious about this. This is the first vehicle I have owned that requires the level to be below the fill.
Im pretty sure its meant to be 1cm below the top of the fill hole. Therefore, it needs to be jacked up so that when it oozes out, but when level again, it would be above the fill plug.
When i did it, I used a giant syringe, and pumped the required amount of fluid into each diff. This is one way to ensure the proper level.
 

sevenhelmet

Full Access Member
Joined
Jul 16, 2007
Messages
649
Reaction score
1
Location
Ridgecrest, CA
I used a gallon fluid pump for mine and had no problems. Just watch out for the little plastic "wingtip" on the fill nozzle of some of them. The little plastic tips can break off inside a gearbox if you aren't careful.

x2 on carefully taking out the fill plug first. One stripped head or torn piece of plastic can ruin your whole day.
 

tjkj2002

Full Access Member
Joined
Dec 17, 2006
Messages
10,612
Reaction score
39
Location
Somewhere between being sane and insane!
Sorry for being so cautious about this. This is the first vehicle I have owned that requires the level to be below the fill.
Just fill till the bottom of the fill hole,no issues will result.

Want a fun diff to fill try a RockJock60 as the cover is laid out at 60 degrees.If I fill to the fill hole I'll blow every seal,I have to add exactly 2.75qts.
 

Squeeto

New Member
Joined
Jan 23, 2012
Messages
5
Reaction score
0
Location
Victoria, Canada
Just fill till the bottom of the fill hole,no issues will result.

This is the 3rd gear oil change that I have done on this truck. Each time I stuck a finger in to try and guess the depth down a cm. Next time I will do as you all say.

Thanks.

I suppose the minds at Jeep don't want the seals to sit in gear oil 24/7 and the extra 1cm was for those of us who park on hills, curbs, the neighbors bike, etc.
 

tjkj2002

Full Access Member
Joined
Dec 17, 2006
Messages
10,612
Reaction score
39
Location
Somewhere between being sane and insane!
This is the 3rd gear oil change that I have done on this truck. Each time I stuck a finger in to try and guess the depth down a cm. Next time I will do as you all say.

Thanks.

I suppose the minds at Jeep don't want the seals to sit in gear oil 24/7 and the extra 1cm was for those of us who park on hills, curbs, the neighbors bike, etc.
The reason is the back fill plug is rubber,just pops in/out.If filled to the bottom of the fill hole it may or maynot weep a little gear oil.

The seals are there to seal,does not matter if they are in constant contact with the oil.No oil touching the seals means no oil in the bearings.
 

Latest posts

Members online

Top