Search results
-
B
Amazing how far into the wilds this Liberty got - Matt's recovery
When I pulled the shaft on my kj after the rear cv decided that it wanted to be a steer and then replace both cv's I did start contemplating u-joints to replace them next time. There is absolutely no articulation going on with that shaft since the diff and transfer case have minimal movement so...- bajasoobnut
- Post #11
- Forum: Videos & Sound Clips
-
B
Shifter bushing elimination fix possibly?
As I stated I replaced the shifter cable system with one from a 05 and this is in a 03, the bushing is the same one that is used in 07 and up wranglers and I have ran across many issues on other forums with bushing failure. The reason why I had to replace the cable and all was because I had a...- bajasoobnut
- Post #3
- Forum: Fabrication
-
B
Shifter bushing elimination fix possibly?
Hey guys, I am now starting to look initially into either modifying or even fabricating a new setup for the transfer case end of the selector system. I replaced the shifter/cable assembly on my 03 to the newer shift assembly from what I believe was a 05 that was in the pick-n-pull near my place...- bajasoobnut
- Thread
- Replies: 5
- Forum: Fabrication
-
B
Just on a search for a cv boot...
Awesome! Thank you! Ordered the complete kit as I might as well clean and regrease the cv joint while I am at it and replace the hardware to insure that it will stay sound for awhile. This is the kit: https://www.driveshaftparts.com/index.php?route=product/product&product_id=970&search=%09ME709BK- bajasoobnut
- Post #4
- Forum: KJ General Discussion
-
B
Just on a search for a cv boot...
Hi guys, I just got done with replacing the transfer case side cv joint on the front driveshaft and ran into a conundrum. I pulled the shaft a couple months back due to the t-case side cv losing all its balls and in the process it looks like it contacted the exhaust pipe, or made some contact at...- bajasoobnut
- Thread
- Replies: 3
- Forum: KJ General Discussion
-
B
4wd shift cable question
oops haven't used this yet but here it is- bajasoobnut
- Post #3
- Forum: How To
-
B
4wd shift cable question
this is the assembly, found the picture on google image search from ebay- bajasoobnut
- Post #2
- Forum: How To
-
B
4wd shift cable question
Hi guys, I had a predicament yesterday while at the beach that had me stuck in 4 low until I had the console pulled apart, shifter pulled out, and the linkage popped off the selector arm on the T-case so I could pop it into 2wd. The main culprit was the cable housing slipped out of the pot metal...- bajasoobnut
- Thread
- 4wd shifter cable help this is a stupid system transfer case cable
- Replies: 2
- Forum: How To
-
B
Transfer case shifter bushing busting
I just went through this myself, the bushing I had to get was 68001899AA btw and it was almost 39 bucks at the stealership!- bajasoobnut
- Post #20
- Forum: KJ General Discussion
-
B
rear cargo shelf
I still have yet to get going on mine, finances are a lil tight but would cost me about 75 in materials and a six pack for labor to punch and bend the sheet metal then Tig weld it all together, I was planning something similar the gate latch and is a hook that hooks into those brackets in a way...- bajasoobnut
- Post #144
- Forum: Fabrication
-
B
Wrangler center console in a KJ
Ok, thanks guys I was just curious if it had been done before. I just am wanting something secure so I can put a pistol and/or valuables into and also have some of the options that I have ran across with the wrangler accessories like a tray that has wireless charging built in and stuff like...- bajasoobnut
- Post #4
- Forum: Fabrication
-
B
Light Bar Bumper Mount
I have been thinking of that and I will be trying this first and then if needed I will definitely make a metal backing that is either sat up with PEM nuts or revnuts for the plate frame and mount to attach to. I am just testing it out and go from there.- bajasoobnut
- Post #7
- Forum: Fabrication
-
B
Light Bar Bumper Mount
I have one drawn up, and will be punched out soon out of stainless, that will mount in between the license plate mount and the bumper and is designed for a 21" LED light bar that I have but can be used for other lights too.- bajasoobnut
- Post #4
- Forum: Fabrication
-
B
Wrangler center console in a KJ
Hey I have searched and searched and I am just wondering if anyone has looked into changing out the libby center console for one from a Wrangler? Reason I am asking is because I want to get one or a few of the accessories that they offer for the Wrangler crowd that replace things like the...- bajasoobnut
- Thread
- Replies: 4
- Forum: Fabrication
-
B
rear cargo shelf
I now have mine drawn up in mastercam so just waiting for the sheet metal guy to flatten them and punch them out on the turret press at work. I will post pics when I finally get it done and also can provide a cad file too if need be.- bajasoobnut
- Post #131
- Forum: Fabrication
-
B
Skid plate dimensions or cad drawings?
Hey guys, I am just wondering if anyone has the dimensions or even cad drawings of the skid plates for a KJ Libby? I work in a model shop with a turret punch and a large sized press brake and think it would be better to fab up the parts and save some money rather than to buy them outright. Any...- bajasoobnut
- Thread
- Replies: 0
- Forum: Fabrication
-
B
missing bump stops...
Ok, thanks guys! The rear stops are totally gone, and better than soapy water is windex, dries quicker- bajasoobnut
- Post #7
- Forum: How To
-
B
missing bump stops...
Ok, if they do get bolted in I will need to know what size, thread pitch and length of screw I will need to get and if it is a shcs or hex headed- bajasoobnut
- Post #3
- Forum: How To
-
B
missing bump stops...
Hi, I have been having some hard bottoming out issues lately and looked underneath the rear today and saw that the bump stops are not even there. So, I am wondering, how are the bump stops mounted? Is it just pushed in? Or is it bolted in? I am planning to replace the rear springs and installing...- bajasoobnut
- Thread
- Replies: 6
- Forum: How To
-
B
rear cargo shelf
New here and saw this as a good idea, been thinking of doing this or a security box. For a shelf I am thinking of making one but out of stainless or aluminum being that I work in a model shop and have access to sheet metal cutting and forming equipment and a tig welder...- bajasoobnut
- Post #129
- Forum: Fabrication
Latest posts
-
-
Rear windshield on 06' Liberty won't close and lock in most of the time.
- Latest: cruisingram2000
-