Search results

  1. J

    Need some help guys...

    I gotta get this squared away! That shuddering feeling / noise is pretty bad... Sounds and feels like my wheels are Egged!! And both were perfectly balanced out to all 0's after the work was done! :(
  2. J

    Need some help guys...

    Could this adversely affect my tires? Or the new bearings I just installed?
  3. J

    Need some help guys...

    Thanks Tom!
  4. J

    Need some help guys...

    Yesterday I changed my cv joints on my front driveshaft, my wheel bearings, lower ball joints, upper ball joints, and tie rod ends because of a whooping sound that developed while driving... Now it feels a lot more solid and stable ... tracks straight and true... and handles much much better...
  5. J

    I must say..

    LoL... I've had about 10 different sets of tires since stock... And these by far have me feeling the most comfortable behind the wheel. :)
  6. J

    I must say..

    MT/R's have restored my faith in Goodyear tires... Night and day compared to 13 years ago riding on the stock SRAs? I swore for the last 13 years that I would never own another Goodyear tire... And found a set of 5 for 100.00!!! With way over 75% in the rear and about 30-40% on the front ones...
  7. J

    Thumping noise in front tire

    Wheel bearing?
  8. J

    Broken Front ball joint!

    Every time it happened I end up having to change just about everything up front lol... This was me being OCD ... But always better to do both sides no matter that your doin.. Upper and Lower ball joints, inner and outer toe rods, R&P bushings, sway bar links, and depending on which side... The...
  9. J

    Broken Front ball joint!

    This has happened to me 3 times in 13 years... Once due to recall... But Chrysler wouldn't cover me for it since I had "modified my suspension"... once due to abuse neglect and stupidity... Once because i used a cheapo replacement part... When #2 happened... Just make sure to change all the...
  10. J

    Where to get wire harness connectors and pins?

    I would love to know the same thing!
  11. J

    Driver side floor board from a wrecked kj near NYC

    Thank you brotha!!
  12. J

    2004 Jeep Liberty - RWD Only?

    I've got the trans and transfer case... Both were purchased based upon my lack of patience when I hear a "noise"... And were not needed lol...
  13. J

    Driver side floor board from a wrecked kj near NYC

    If anyone knows of any unfortunate kj anywhere in the tri state area that I could cut the driver side floorboard out of it would be great! Or if anyone has a junker laying around that would be wiling to do this for me... It would be even better! Here's some pics of the damaged area... There's...
  14. J

    Was wondering why my feet were wet this morning..

    Oooooohhhhh that would be awesome !!
  15. J

    Was wondering why my feet were wet this morning..

    On a side note... It snowed last night and its raining today... I had to go out driving around for a couple of hours this morning... and the gorilla tape job held up 100% so far lol... It just has to last till I can get to the body shop till later... But man that stuff is tough!
  16. J

    Was wondering why my feet were wet this morning..

    The rest of the underbody is clean as a whistle... It's almost like i had a small hole before my beach adventures which were many... To say the least... I was always gung ho about not giving a f' when it came down to sand getting in my car... And I have that hole in my carpet where my right heel...
  17. J

    Was wondering why my feet were wet this morning..

    Lesson kiddies: get all the sand out of your car when you go to the beach... I found about 2lbs of sand under my carpet ...
  18. J

    Was wondering why my feet were wet this morning..

    Oh boy... I hope she can be saved! Here's what I found today :( I made an appointment to have it looked at tomorrow :( in the meantime... Gorilla tape is my friend :) ... I managed to seal it up over and under as best as I could and also put a piece of plastic under the wire harness...
  19. J

    Do I have everything lol...

    I bought a moog replacement for the rear I think it should be fine.
  20. J

    Do I have everything lol...

    On a side note I feel as though I can take the new knuckles, bearings, and lower ball joints to the machine shop... Have them put together and just straight swap them along with the upper ball joints without needing a wheel alignment... Am I correct in my assumption??

Random media

Before Mesh inserts
in the shop at school becuz a mounting bracket came loose on the push bar from everyone leaning and jumping on it
wife and me in Vegas
Picture 234
IMG 20160922 153548
2980.jpg
After lift
IMG 1167
DSC01741

Latest posts

Members online

Total: 268 (members: 4, guests: 264)
Top