Recent content by 604KJ
-
so many noises!
Hi All, I was out wheeling yesterday, got under the front end at one point and found that my brand new JBA extended sway bar link (Drivers side) had popped right off the bushing. I'd never seen anything like that before. Thought it was odd so i just took the thing off, passenger side too. I've...- 604KJ
- Thread
- Replies: 1
- Forum: KJ General Discussion
-
dash vents
does any1 know if the nice wrangler dash vents can replace the libertys?- 604KJ
- Thread
- Replies: 0
- Forum: Fabrication
-
KJ Tri-Angulated Bolt On 4 Link from JBA
good idea, that makes sense since I would truss the rear anyway. Using one of these in the rear, for SFA purposes....would that take care of the need for control arms?- 604KJ
- Post #55
- Forum: Lift Kit Discussion
-
KJ Tri-Angulated Bolt On 4 Link from JBA
would this be an ideal upgrade for a sfa KJ? Do you need to have the Y-link extension for this?- 604KJ
- Post #52
- Forum: Lift Kit Discussion
-
Install AC Compressor Clutch?
Well, I finally got this fixed. :) I bought a Dremel, cut that piece off the shaft and from there it was simply putting the new stuff on. I don't know what caused my bearings to come out and grind everything up, but I've had the new one on for a week now and everything seems to be working... -
How do I make my jeep look like this?
I contacted those guys anyway: We currently do not have any HP Dana 44’s.... all of the older Broncos (71-77) were a low pinion Dana 44, 78 and newer were high pinions... So, with this being said, the axles you see on our web are low pinions... thanks!- 604KJ
- Post #31
- Forum: Lift Kit Discussion
-
How do I make my jeep look like this?
I'm ok with that, + it will keep things easier for me as far as modding the D44 goes right? If i were to have a d44 stock width custom built, what would that look like? I found this website.. are these worth it, and how can you tell if theyll fit...- 604KJ
- Post #30
- Forum: Lift Kit Discussion
-
How do I make my jeep look like this?
So this is completely new to me, what is the difference between having separate shocks and coils vs coilovers?- 604KJ
- Post #28
- Forum: Lift Kit Discussion
-
How do I make my jeep look like this?
Wouldnt having a shorter axle with spacers be an easy weak spot if i want 35's? I want the stance to match front and rear. New wheels are on the list already- 604KJ
- Post #26
- Forum: Lift Kit Discussion
-
How do I make my jeep look like this?
Thanks TJ, is that what you have too? I know I've still got a ton of research to do, but could you answer these questions to help me better understand some things? D44 - Does that have to be from a 75-77 Ford F100/F150? I don't imagine it will be easy to find something so specific out my...- 604KJ
- Post #24
- Forum: Lift Kit Discussion
-
How do I make my jeep look like this?
Im going to shoot for a SFA conversion. I'm not loaded, so I plan on spreading this out over a year or 2 to help with the costs, doing plenty of research and gathering pieces in the meantime. Been doing a lot of reading over on the lost forums for a while now..I think if I take this slowly I can...- 604KJ
- Post #20
- Forum: Lift Kit Discussion
-
Install AC Compressor Clutch?
I was thinking about that, I figured at this point if I ruin anything either way I will need a whole new unit. OK, I'm doing this tomorrow morning and will let you know how it goes. Thanks! -
Install AC Compressor Clutch?
I've discovered what the problem is! By comparing the old pulley to the new one, I realized that the old bearing assembly in the centre of the pulley has been ground out by the ball bearings inside, and some of it seems to have fused itself onto the compressor shaft, creating those lips I was... -
How do I make my jeep look like this?
I'm often questioned about my tie rod ends every time i'm in for an alignment or tire services... they say they're extreme and look like they will break...Whats an upgrade for this then? basically what I'd like to do is put together a list of parts necessary for a lift like yourself.... and...- 604KJ
- Post #17
- Forum: Lift Kit Discussion
-
How do I make my jeep look like this?
Hey Tom, I measured this morning and I'm 22" in the front. What part of this number equals my lift amount? I'm up for making the investment on something like the IFS 4" lift (or more if possible), what all would be required to do this properly?- 604KJ
- Post #15
- Forum: Lift Kit Discussion
