Ever figure this out? I installed the kit back when they had the harness available as a separate part so i have some idea of what I'm doing. You'll need to route the wires under the tipm and put pins on the end to put into the connector. My advice would be to go to a pick and pull and snip the...
If you do the cluster self-test by holding the trip reset in as you turn the key from acc to on (not start), you'll see two icons on the right above the coolant dial. It looks like they are diff related. Someone else suggested it might be for the brake lock differential. Anyone here know more...
It's not a TSB per se, but it was published with other ones. I don't know what the right term would be but it is listed as "X46 lifetime warranty extension"
If any other people have been having this issue, a TSB was just published yesterday that extends the warranty on the gas tank for the life of the Jeep. It might take a while to show up in the warranty system, so it may be a few weeks still before you can schedule an appointment. Since they have...
I'm in the planning stages right now for one. I have a model I can show you all but it is not to scale. I'm thinking of using aluminum angle iron to bolt down to the roof and have the cross bars bolt/weld to those. I also have a rear bumper/quarter guard that comes down from the roof and...
I was going to go with the OME2927 springs (3.7HD) up front and the OME2731 in the back. Are the springs you're recommending the CRD HD springs?
As far as the struts go, I only see the option for the NS131 on the fronts. That should be a bit longer than stock, right?
I want to get around 2". Do I need any more parts? If I use a strut spacer up front, do I need to add anything in back?
Springs n shocks:
JeepinbyAl.com - Detail1 - OME-KK-1.5-3.7 - OME 1.50" lift kit - Old Man Emu Suspension Products - Jeep Liberty KK (2008 plus) - JeepinbyAl.com...
Is it only the Trac/ABS lights, or is it all the lights in this picture? If its the ESP/BAS and Serv 4WD as well, its probably a wheel speed sensor or associated wiring. Is the dealer reading the codes via the WiTech or just a standard OBDII reader? ABS codes are stored for about 50 key cycles...
I'm looking into making a steel bumper plate like the backbone with a aluminum fascia to save on weight on my KK. That way I can have a winch and better front clearance without a lot of added weight.
I found out the issue: apparently, some models have a door module that the mirror plugs into, as well as the seat/mirror memories and door harness and that's why there is a different connector. I fixed the problem anyway by popping off the old connectors and putting them on the new mirrors and...
Here is the site I got my wiring info from: http://dto.vftis.com/mopar/connreview/reviewconn.asp?chk=132086xxMIRROR-OUTSIDE+REARVIEW-PASSENGER+%28BASE%29+-+%28PASSENGER+DOOR%29+8+WAY
In the door harness, there are 5 pins. 3 for movement, 2 for heat. The attached wires match the colors given...
I did check to make sure the wiring was there before I bought them, the only problem is the mirror connector is 10pin while the harness is 8pin. Is there a place where I could get just the connectors to switch? I would use the normal mirror's, but I can't get the pins out. If it comes down to...
I was thinking of doing that, I'm just not sure what wire it would be. From what I've seen, it should be white/purple. I can't find a pinout for it, but I could probably figure it out with a multimeter. I also found a circuit labeled "PANEL LAMPS DRIVER" which may be an easier choice.
I want to add LEDs that come on with the backlights of the gauges and radio. Because it will be low current, I was going to run a MOSFET off of the parking light signal to control them. My first thought was the main harness, but that seems like it would be a pain with all the other wires to dig...
Here is a brief schematic I drew. Tap into the signal to the parking light relay and use that to trigger a normally open relay. This will only allow current to flow through it when the park lights are on. By having the current flow then flow through a normally closed relay triggered by the fogs...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.