Search results

Removed the harmonic balancer and still vibrating on acceleration around 100 km/hr Engine mounts are good Can it be front shaft ? Heard something about transfer case bearings ,any one have experience with that ? Thanks in advance guys Regards, Ahmed Regards, Ahmed KJ 2007

Thanks lot, My KJ has 250Km now, before replacement of u joints it was vibrating badly, now only starting 100km/h and above I tried to make the mechanic keep shaft in same orientation as it was and he says he did but I'm not so sure If I remove that harmonic disc it can be installed again ...

I'm talking about the big harmonic balancer disc on the rear drive shaft Don't have a pic Regards, Ahmed KJ 2007

very interesting thread, really admire your fighting spirit :) I Have the similar vibration on GAS but at any speed today i replaced rear u-joints with spicer sealed ones non-greaseable vibration got much better but around 100-120 Kmh its there curious how did you remove that harmonic balance...

After removing old rear right sensor found lot of metal dirt stuck on it, cleaned it and and measured it and it shows around 380k again :) Connected it back and no alarms since then Thought I update u guys Thanks, Ahmed Sent from my ONEPLUS A5000 using Tapatalk

I have new one for the front ,and it measures around the same 380k ,just wanted to see if u guys tried this before, Am getting rear sensor Saturday hopefully this solve the problem Sent from my ONEPLUS A5000 using Tapatalk

I guess u have one sensor in back, mine is 2007 it has 2 in back, one per wheel Sent from my ONEPLUS A5000 using Tapatalk

Hello Guys, I have 2007 liberty sport with 220K on clock recently i got ABS, ESB, Handbrake and slide marks lights on in the dashboard i have read a lot and found a common issue about rear sensors wires, i did ohm test straight from ABS module connector after disconnecting the senors...

Just checked , Found both sides still in place , If I disconnect it anyway to test or measure if it's good ? Br, Ahmed

Hello guys , Thanks for your support , I'm trying to figure out which sensor it is ,tried different obd scanners and no luck Bough the obdlink mx ,still shows nothing Tried turning key 3 times also not showing anything Anyway to find which sensor is bad ? Thank you

where is this sensor connected , if i want to replace it its coming with long wire and connector , BR, Ahmed

thank you guys for reply , battery is new and fuse is ok i checked already one guy told me its a bad speed sensor on one of the wheels will make such errors i checked with Bullydog tunner also ,it shows no codes but when i clear faults leds are off till i drive few kms leds are on again do you...

hello experts :) , my liberty 2007 A/T been going very well even in hot weather we have in Dubai , recently got the ABS ,ESB and slide marks LED ON while on the high way jeep drives normally ,except for ABS kicks in randomly when i start it morning and start moving i have OBD2...

snorkel still there ? how much ?

yeah was thinking the same ,but don't know about any company or shop selling such thing. any idea ?

Hello Luke , correct that what i was also thinking ,but i doesn't move it enough to be away from spring ,i explained the to alignment guy and he moved LCA to max away from spring and it still touch it . it only happens when i go over a peed bump or offroading in desert and car kinda jump a...

Hello Guys, I have done alignment already ,again camber and toe are ok caster is on max adjust and out of range ,but mechanic says it looks fine , still have the same issue, i was thinking to use some rubber stopper under the UCA (where the two bushings are fixed) so it stop the UCA from...

Hello Experts, thank you for your inputs, the jeep drives fine and straight on high way that's why i thought alignment is ok. also i wana know ,in the alignment the springs can move closer or away from UCA ?

Yeah I should do alignment I know ,just didn't have enough time plus not easy to find someone know what he is doing over here specially with lifted jeeps I agree with you 21 inch is not that high ,but what could be wrong ? I mean what are the possibilities ?

:ban: Hi Bob, I have OME HD complete setup coils and shocks with 20,000 KM on them now ,and yes I have long bump stop and its touching the UCA when traveling up. I have no spacers on top, just 7 mm ring bottom of the shock, but I had the same issue before installing it also (didn't do...