Search results
-
Angry Eye for KJ
I had them painted with night shade at first, then when I bedlined the entire Jeep I went over the headlights with it. I have no problems with light output using the headlights alone. Sent from my SM-G955U1 using Tapatalk- Sephiroth
- Post #9
- Forum: KJ General Discussion
-
Heater problem
A stuck open thermostat would not give you heat at that speed as the coolant would not stop circulating through the radiator not reaching temperature, a stuck closed thermostat would cause the engine to overheat as coolant would not flow through the radiator. What does your temp Gage say? Are...- Sephiroth
- Post #5
- Forum: KJ General Discussion
-
Did i mess up? 4.10 gears
I ordered the D30KJ-410LIB-OE spicer 4.10 gears for the front of my liberty which has the OEM differential, but I've seen a different set of 4.10 gears at JBA's website with no part number listed as 2002-2005 Jeep Liberty KJ aluminum housing what's the difference between this 2? will the spicer...- Sephiroth
- Thread
- Replies: 0
- Forum: KJ General Discussion
-
Catastrophic Brake Failure - Dont Wait for it to happen to you!
are this the lines behind the wheels or under the hood? I replaced mine with braided lines a couple of years ago, I'm driving 1100+ miles next weekend wouldn't want this to happen.- Sephiroth
- Post #6
- Forum: KJ General Discussion
-
JBA wheels?
I do plant to go with 265/70 eventually, I just wanted to make sure I can continue to use my current set 245/75 till I'm ready for new tires. Planning on getting 4:10 gears as well just not sure if before or after the tires. Sent from my SM-G955U1 using Tapatalk- Sephiroth
- Post #5
- Forum: Tires / Wheels
-
why can't i close my steering rack bolts?
There are 2 nuts under the cross member that the rack bolts on to. Make sure to hold then with a wrench so they don't just spin. Sent from my SM-G955U1 using Tapatalk- Sephiroth
- Post #2
- Forum: KJ General Discussion
-
JBA wheels?
So look for something with 5 inches of backspace, got it. Sent from my SM-G955U1 using Tapatalk- Sephiroth
- Post #3
- Forum: Tires / Wheels
-
JBA wheels?
I've been looking at the wheels from the JBA website, Baja 16x8 I'm currently running the OEM steel wheels with 245/75/16 tires and have a small amount of rubbing at full lock when in reverse with the OME lift, top plate, and clevis. can I fit this wheels without any major problem? and can I use...- Sephiroth
- Thread
- Replies: 4
- Forum: Tires / Wheels
-
Misfire and roughness help
Check the ignition coil in cylinder number 3 middle passenger side if I remember, start the engine unplug the coil pack and check for a drop in RPM if no drop happens change coil in cylinder 3 to cylinder 1, and cylinder 1 to cylinder 3 and unplug again, if the misfire (no drop in RPM) moves to...- Sephiroth
- Post #2
- Forum: KJ General Discussion
-
Drilled a hole in my intake manifold today
Take the valve covers off and make sure everything seems ok in there, no broken or lose parts you should not be able to move anything be hand, the IAC is located at the trhottle body under the position censor make sure it's port is clean and you could test it by screwing in the plunger and put...- Sephiroth
- Post #7
- Forum: KJ General Discussion
-
Radiator Fan issues
Have you tried rock auto, got mine from them. Sent from my SM-G955U1 using Tapatalk- Sephiroth
- Post #2
- Forum: KJ General Discussion
-
Drilled a hole in my intake manifold today
You have successfully created a vacuum leak, check your long term fuel trim, you're probably running lean I would have tried an IAC before drilling your manifold, it's probably sticking and choking the engine at idle, now you need a new intake, the knock could be rocker arm, do you have a cel...- Sephiroth
- Post #2
- Forum: KJ General Discussion
-
hood release feel
I had to pull mine all the way and then some for the hood to open. I changed the cable and fixed the problem, it's a cable, it eventually stretches making you have to pull more the handle. Sent from my SM-G955U1 using Tapatalk- Sephiroth
- Post #5
- Forum: KJ General Discussion
-
What did you do to your jeep today?
Got some hood vents installed along with HD cooling Sent from my SM-G955U1 using Tapatalk- Sephiroth
- Post #17,552
- Forum: KJ General Discussion
-
Large Evap leak
So I just replaced the gas cap with an OEM as well as the Evap purge valve, ( not OEM) cleared the CEL but now the new purge Valve is making some wired noices, pretty sure that's not normal http://imgur.com/gallery/rRia33L Sent from my SM-G955U1 using Tapatalk- Sephiroth
- Thread
- Replies: 2
- Forum: KJ General Discussion
-
Emergency HELP!!!
Did you flush it? Sounds like it might have an instruction somewhere Sent from my SM-G955U1 using Tapatalk- Sephiroth
- Post #5
- Forum: KJ General Discussion
-
Emergency HELP!!!
Get a pigtail from a wreck yard swap it out and done Sent from my SM-G955U1 using Tapatalk- Sephiroth
- Post #3
- Forum: KJ General Discussion
-
What did you do to your jeep today?
installed a roof rack, greased the UCA ball joints and discovered a leaking radiator...- Sephiroth
- Post #17,363
- Forum: KJ General Discussion
-
CV Joint?
That's what I paid to have mine replaced a few years back, I did not know that there's a kit to fix it much cheaper JBA sells it you should look into that if that's what's wrong, but it doesn't sound like it to me, they usually start clicking and they click faster as you drive faster. Sent from...- Sephiroth
- Post #5
- Forum: KJ General Discussion
-
CV Joint?
Does the noice increase the faster you drive? The front drive shaft will start clicking when it goes bad, The ratcheting noice after shifting is normal mine has done it for the past 9 years without any problems. If you have ever done a break job your should be able to pull a CV without problems...- Sephiroth
- Post #3
- Forum: KJ General Discussion
