Search results

  1. Zero402

    What did you do to your jeep today?

    Been striping the interior for the last couple days to swap it out. While its gutted, will run cables for new sound system and also front and rear lighting. Also finally installed the JBA uppers but putting all new front end components on also, just waiting on parts.
  2. Zero402

    Pass side axle C clip removal?

    Yea, i ordered one today ( intermediate shaft ). After I posted this, I was browsing the site since Im stuck and cant go anywhere, I saw a post where you stated they should be changed same time with axle half. Guess now Ill be cleaning the inside since I cant drive it haha
  3. Zero402

    Pass side axle C clip removal?

    Shot... Yes Im replacing both cv axle halfs. Well I guess i dont have a vehicle now till I can find one and have it delivered. Thanks
  4. Zero402

    Pass side axle C clip removal?

    So I am rebuilding the front end. I have the axle half and intermediate shaft out and separated. How do you get the C clip out of the female portion of the axle half? My snap ring pliers wont do it because you cant expand the C clip because of outer wall of the axle half.
  5. Zero402

    02 dashboard into an 04

    I thought the dashboard's were the same ( based off model years ) But I noticed that the 02 has 2 bolts that hold the metal frame to the side foot panels as where the 04 there is only one bolt. Before I pull out the 04, will it not fit correctly, if anyone knows? Thank you
  6. Zero402

    Busted bolt on thermo housing

    Thanks for the tip. Extractor was still in. What a pain in the ass. I got it though. Had to drill tiny holes round the broken bolt to where it was punched out, then cleaned up hole and used a nut and bolt to secure.
  7. Zero402

    Busted bolt on thermo housing

    Anyone ever have this happen? Mine just broke off inside the pin area. I was able to drill a hole in the center of it, but then the extractor broke off in the newly drilled hole. Has anyone drilled straight thru to put on a new bolt and nut? Anyone have to drill it out and use a helicoil? How...
  8. Zero402

    Sagging OME springs?

    duderz7, I can understand your point, but if they cleared with no rubbing issues lets say Oct, full turn left right forward and reverse and then rub in January, so you trim, and you are all clear again in all directions and it starts to rub in March, wouldn't you suspect something wrong with the...
  9. Zero402

    Sagging OME springs?

    1/4" top plate Clevis lift 265/75-16 mounted on 16x8
  10. Zero402

    Sagging OME springs?

    less than 15k 2 years OME 948's and OME 927's Bilstein Fender trim and other misc plastic underneath. Not to mention, my front have no tread left either. I wouldn't be able to drive it if it had tread. Edit: the lift is pretty much what everyone here has done
  11. Zero402

    Sagging OME springs?

    I am constantly shaving something from my underside. I waited almost a year before doing any kind of clearance work. Every couple of months, it begins to rub. I cut away material, its good for a few more months then it starts to rub again. Is this normal ( Im thinking not, at least not this soon...
  12. Zero402

    Tires wearing odd

    cooper discoverer stt pro
  13. Zero402

    Tires wearing odd

    Estimate of 10k on em. Havent rotated i know i know Alignment, to my knowledge othe than camber Everything new except lcas Mostly town yes. The front suspension seems very hard also. When i hit a bump, depending on speed, passengers have let out explicit words. Could it be the springs? Weny...
  14. Zero402

    Tires wearing odd

  15. Zero402

    Tires wearing odd

    Tires are wearing odd on the front. All new suspension with exception of lower a arm. My camber is sligjtly off on pass side bit that doesnt explain the wear pattern ot even why on drivers side. Each lug kind of ramps up to the next lug in front of it. Hoping you can tell by photo.
  16. Zero402

    Spring clearance question

    So lemme ask this, cause I just noticed it. Is this part of the design flaw you mention? Notice the bolt heads for the endlinks, pass side is pushed further down compared to drivers side, meaning greater angle. I checked measurement and its a 1/2" difference. That the flaw issue ? Is that spring...
  17. Zero402

    Spring clearance question

    :signs8: :grd:
  18. Zero402

    Spring clearance question

    Oh I know I need UCA's, soon will be done, I was just curious as to the difference in gapping.
  19. Zero402

    Spring clearance question

    Aside from an unknown accident to me, what would cause such a difference in UCA to spring gapping? Driver's side nice clearance, pass side clangs on a pebble. Ome springs 1/4 top plate Kk clevis
  20. Zero402

    Spacer

    I don't know what you are referencing to as far as the "wing". There is plenty of plastic down there that can be trimmed. Its also possible you will need to "fold" the pinch weld. What are you currently rubbing on? Any photos?

Random media

Lifted, new tires and wheels
Before lift and new tires/wheels
Got stuck while doing some night wheeling
image
Winter '12-'13
Manistee National Forest (MI)
Picture 233
1169.jpg
a1

Latest posts

Members online

No members online now.
Total: 219 (members: 0, guests: 219)
Top