Search results
-
Rough Idle/CELs?
I finally got a chance to pull the reading for the fuel trims. At an idle they were: STFT B1 -.08% LTFT B1 5.5% STFT B2 -2.3% LTFT B2 7.0% Obviously they flucuated, but thats a general representation as how they were at an idle. Under acceleration they changed to higher...- bmrrwolfe
- Post #17
- Forum: KJ General Discussion
-
Rough Idle/CELs?
On my scan tool, (craftsman) it does not show any charts like yours.. After scanning it show the errors a and freeze frame of about 28 abbreviations and numbers. (I have two pics from the first page of this thread) The first two abbreviations: "FUEL SYS 1- CL" "FUEL SYS 2- CL-FAULT" So...- bmrrwolfe
- Post #15
- Forum: KJ General Discussion
-
Rough Idle/CELs?
02 Sensor will be done on Friday, and I will be doing new NGK V-power plugs at the same time. Scanning after work today, I found a "fuel system 2 CL-Fault" any ideas??- bmrrwolfe
- Post #13
- Forum: KJ General Discussion
-
Rough Idle/CELs?
The traction control is not of any concern at this point. Drove home and for an 5 mins around the neighborhood and no stumbles at all and normal power. Ran the scanner again, and again no CEL but it showed: P0420 P0430 P0171 P0174 and the 02 sensor code disappeared.. I used...- bmrrwolfe
- Post #11
- Forum: KJ General Discussion
-
Rough Idle/CELs?
Thanks for the information. Also on the traction control issue, I was just pointing out what I have seen from people with similar issues, I will not be doing anything with the suspension unless the problem persists, and even then, I would just get an alignment when I decide to put on new tires...- bmrrwolfe
- Post #9
- Forum: KJ General Discussion
-
Rough Idle/CELs?
Attached a couple numbers from the scan tool doing a live scan while it was idling in the driveway. Not sure if that helps with anything, as they seem to fluctuate a lot.. A good half hour of driving around, it feels normal, the idle sits at about 600 (normal) does not shake or have a rough...- bmrrwolfe
- Post #7
- Forum: KJ General Discussion
-
Rough Idle/CELs?
Well after adding the gas treatment and 8 gallons of 89, let it run for a few mins to work into the fuel system and I did about 15 minutes of suburb driving (most of driving is suburb driving about 4 miles each way to work) it did not have the rough idle it had before at stops. The CEL did not...- bmrrwolfe
- Post #5
- Forum: KJ General Discussion
-
Rough Idle/CELs?
NGK Plugs are copper and have about 18k on them, and will be done again in the summer. Gas is not E85. Few stations around here have it, and this is one of 3 three stations that I go to regularly, but just incase it is a gas problem, I got some gumout gas treatment and added gas. Put a few...- bmrrwolfe
- Post #3
- Forum: KJ General Discussion
-
Rough Idle/CELs?
The CEL came on the Jeep this morning driving to work, but seemed fine when driving. On the way home it seemed to start running a little rough at idle, but ran fine under any load. Also if you shift the tranny into park, the idle seemed to improve, and not have the shake it had in gear. When...- bmrrwolfe
- Thread
- Replies: 30
- Forum: KJ General Discussion
-
Adding Power Heated Seats without Factory Wiring?
Thanks, and I do have the factory service manual, but the location of the #1 circuit breaker is very tight and hard to get to, and I could not find if all KJs have the wiring coming off of it, and if so, where that wire goes to if it doesn't go all the way to the seat.. The same thing goes for...- bmrrwolfe
- Post #3
- Forum: KJ General Discussion
-
Adding Power Heated Seats without Factory Wiring?
I have installed some leather power heated seats from a 06 KJ limited, but found under my seat, I do not have the wiring ran to my seat for the power & heat that most people have (in my case only have wiring for the seatbelt) Now I tried to trace the wiring back to how the factory wiring would...- bmrrwolfe
- Thread
- Replies: 2
- Forum: KJ General Discussion
-
2006 KJ Gray Cloth Seats
Ironically the new seats came from NC where my dad lives, and I swapped them in down there and brought the old ones back here...- bmrrwolfe
- Post #4
- Forum: For Sale Forum
-
profdlp's 2007 Liberty Project
I have 6" lights, but have them mounted low, and I think my crossbars sit a little lower on mine as well, but I think you'll be fine, now if you lift it and throw 32s on it, then you might need to start worrying!- bmrrwolfe
- Post #45
- Forum: Members' Journals
-
2006 KJ Gray Cloth Seats
I have a set of seats out of my 06 KJ, that I swapped leather seats into. The drivers seat has a tear in a seam, and the other seats are dirty, but clean up decently. Has a burn hole or two from the PO. They include the seat frames, as well everything from the OCM for the passenger seat (the...- bmrrwolfe
- Thread
- Replies: 4
- Forum: For Sale Forum
-
2003 Liberty EVIC with Homeline & Sunroof
Sounds good, just let me this weekend.- bmrrwolfe
- Post #3
- Forum: For Sale Forum
-
-
profdlp's 2007 Liberty Project
Yupp, those do have a higher lumen output and are a flood beam, but only have one review. For my wiring I have relays being powered off the "remote" wire that comes out of the aftermarket stereo to the amp. I figured this way they are only on when the stereo is on, and I can easily remove...- bmrrwolfe
- Post #42
- Forum: Members' Journals
-
profdlp's 2007 Liberty Project
The lumen outputs seems a little low, and they are floods so they will have a wide very short beam. I am not sure if that is what you are looking for, but ideally I would look for a set of 4, with 2 spot and flood, or a pair of these...- bmrrwolfe
- Post #40
- Forum: Members' Journals
-
My 2006 Jeep Liberty
A little update: Added a double din Pioneer. Modified the dash trim to fit, just a real quick bondo job and a little paint. Could of been a lot nicer, but hey, its a Jeep not a show car. I did measure off about 1/32" so when pressing it in the upper right corner hit the stereo and cracked...- bmrrwolfe
- Post #33
- Forum: Members' Journals
-
profdlp's 2007 Liberty Project
Yupp that would be me. I have to say the rack looks good!- bmrrwolfe
- Post #38
- Forum: Members' Journals
