Recent content by JMichael2006

  1. JMichael2006

    Rear Upper Control Arm (Boomerang)

    Yes, it will work fine on a stock height truck as well.
  2. JMichael2006

    Need help selling a NSG370

    Unbolt the output flange in the tail housing, I believe you'll find the setup for 4x4.
  3. JMichael2006

    Need help selling a NSG370

    I found the rear housing for it on E-Bay for $260. You could just rebuild it as a 4x4 unit.
  4. JMichael2006

    2.8 CRD Cherokee KJ overheating when A/c on

    Okay, didn't know the Euro versions didn't have Efans. I also installed the 10 blade fan and clutch off a Chevy v8. Check the image, it has all the p/n's to install a better setup.
  5. JMichael2006

    2.8 CRD Cherokee KJ overheating when A/c on

    My front fan failed (old,corrosion,..), it would over heat climbing a grade. I replaced it with an aftermarket single speed the same size. It is back to running like it is supposed to. I just pulled the assembly. Removed the old motor and blade assembly from the Jeep mount. I then installed the...
  6. JMichael2006

    2008 KK Hum/Roar Noise Front/Passenger

    Check your RF hub, I would venture you have a bearing going.
  7. JMichael2006

    Front hub with ABS on non-ABS Libby

    Leave the ABS wire and sensor installed, just tie it off and fill the connector with dielectric grease.
  8. JMichael2006

    05 crd with power loss. Limp mode

    Check IDParts, they have them for $59. They are a great source for these Jeeps.
  9. JMichael2006

    Please help. Where to get another non-used engine?

    I have used Jasper engine before for customer cars of all types. We have taken Jasper reman's and warmed them up with good results. They have good quality work and components.
  10. JMichael2006

    Been A Year - Let's Get This Going Again!

    Camping set-up on Libby I have an old M100 that I am thinking of moving the RTT to, set it at the top rail of the trailer so it is a hop up instead of climb up. I like the compact size. Maybe seal the top of the trailer and load the kitchen and such in it with long drawers like the pickups have.
  11. JMichael2006

    Been A Year - Let's Get This Going Again!

    Camping set-up on Libby
  12. JMichael2006

    Side Sills

    They show doing inners and outers, because I need both. My other option is to weld in rectangular tube and make rock rails out of them.
  13. JMichael2006

    Side Sills

    There is c2cfabrication.com in Redford, MI that makes them for $80 each.
  14. JMichael2006

    What did you do to your jeep today?

    Rebuilt the rear suspension this weekend. Shocks, K member, lower arms and fresh springs. The surprise wiggles gone! Next weekend, the front gets hit.
  15. JMichael2006

    Modifying the Rockfather Lift

    You just move the clamp on the bottom of the shock down 1/4", which is usually what is sticking out the bottom of the clamp. You end up with the same surface clamp area as without them, just in a different spot.
See more

Random media

20121125 161013
The damage that bought me an ARB
IMG 20140405 160049 375
Alignment/Testing
DSC01239
Torque Jeep Liberty Lugs
IMG 1157 (1280x933) 4-11-14
jeep10
Rear tube bumper on 1991 toyota

Latest posts

Members online

Total: 577 (members: 2, guests: 575)
Top