Recent content by goob2k
-
maglite mount
It's just 4 little tiny holes. One of the most useful mods I've done.- goob2k
- Post #9
- Forum: KJ General Discussion
-
HOW TO: Install an EVIC or OTIS (overhead computer)
I got one of those add-a-fuse gizmos that splits a circuit (I think it was talked about earlier in the thread). I plugged it into the spot for the BCM (I think it is #13 on the interior fuse panel). For the new circuit that went to the EVIC, I used a 2 Amp fuse since it was the smallest rated... -
another craigslist libby
I emailed him about the lightbar around 3:30 PM yesterday. Never got a reply. :(- goob2k
- Post #12
- Forum: KJ General Discussion
-
mopar front engine skid
The skid already had the brackets attached. I bought the skid off moparpartsamerica.com for $48.96 + shipping. Their catalog listed the cheaper bracketless skid (and didn't list this newer one). After I placed the order, they said that Chrysler had revised the skid and wanted me to confirm...- goob2k
- Post #8
- Forum: KJ General Discussion
-
mopar front engine skid
I just put the front skid on my 06 last weekend. It already had those brackets attached. It was part # 82210769.- goob2k
- Post #6
- Forum: KJ General Discussion
-
HOW TO: Install an EVIC or OTIS (overhead computer)
You're supposed to remove the A pillar covers and the sun visors. That will give you enough room to slide the bracket above the headliner. -
Dana 30 Detroit Tru Trac
Well this guy with a funny name would like to buy it this time :). I've got my paypal ready.- goob2k
- Post #13
- Forum: For Sale Forum
-
HOW TO: Install an EVIC or OTIS (overhead computer)
Hmm, I might try that. The section towards the windshield is holding fine, but the section towards the back is what came loose. -
HOW TO: Install an EVIC or OTIS (overhead computer)
For those of you that had to add the bracket, what sort of adhesive did you use? I used some heavy duty double-stick tape but I guess it wasn't heavy-duty enough and one section came loose. Any suggestions? -
Detroit TrueTrac (Front and Rear)
I'm on the hunt for TrueTracs for the front and rear of my KJ. If you have one that you'd like to get rid let me know. The part numbers are: 912A553 for the Chrysler 8.25 rear 912a585 for the Dana 30 front (912A314 is an older model, I'm open to that as well). Let me know what you've got.- goob2k
- Thread
- Replies: 0
- Forum: Wanted To Buy
-
-
KK Seats into KJ?
Are the KK rear seats the same dimensions as the KJ rear seats? I wouldn't mind swapping in KK front seats, but the fact that the rears didn't match would bug me.- goob2k
- Post #34
- Forum: KJ General Discussion
-
Please Help! 2002 KJ interior bulb question...
What's the procedure to get under the shift bezel? Does it just pop out?- goob2k
- Post #6
- Forum: KJ General Discussion
-
Interior light?
I have an 06 with a sunroof. I just have the map lights up front and the cargo light. I guess a light over the back seat would get in the way of the sunroof.- goob2k
- Post #10
- Forum: KJ General Discussion
-
HOW TO: Install an EVIC or OTIS (overhead computer)
One with sunroof controls will work fine. You'll just have the sunroof buttons but they won't be connected to anything. You could always find a non-sunroof housing later and you could put the 07 EVIC module into that one if the non-functional sunroof controls bugged you.
Staff online
-
LibertyTCWell-Known Member