Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New resources
Latest activity
Media
New media
New comments
Search media
Resources
Latest reviews
Search resources
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
WWDiesel
Full Access Member
·
From
Central Georgia
Joined
Dec 15, 2013
Last seen
Yesterday at 1:43 PM
Messages
60
Reaction score
60
Points
18
Find
Find content
Find all content by WWDiesel
Find all threads by WWDiesel
Latest activity
Postings
About
WWDiesel
replied to the thread
CRD 2.8 2005 Harmonic Balancer inspection
.
Your viscous heater can be deleted if you want, pm if interested. Damper Doctor can rebuild your harmonic balance...
Yesterday at 1:43 PM
WWDiesel
replied to the thread
CRD Throttle Issue
.
Which red light on dash? Was it #29 on the diagram shown? If so, replace the accelerator sensor and / or check the wiring connector.
Sunday at 12:33 PM
WWDiesel
reacted to
u2slow's post
in the thread
Can I get an alignment before rear control arm replacement?
with
Like
.
The alignment is done on the front. There is nothing to adjust on the rear.
May 10, 2025
WWDiesel
replied to the thread
KBDiesel silicon Turbo Intake Hose (small port placement no good)
.
The silicone air intake hose is definitely a tight fit, I have a Sasquatch one on my Jeep with ProVent. I used a 90 deg. metal elbow to...
May 3, 2025
WWDiesel
replied to the thread
CRD running hot?
.
What the marks on the temperature gauge represent. Normally it should run very close to the 176 deg. mark. Just slightly below the...
Apr 22, 2025
WWDiesel
reacted to
duderz7's post
in the thread
Rear Upper Control Arm (Boomerang)
with
Haha
.
is this turning into a show off your IRO?... Or did I totally miss the social que?
Apr 22, 2025
WWDiesel
replied to the thread
Rear Upper Control Arm (Boomerang)
.
Yes, it will work perfectly with stock height vehicle. I have installed several of them on stock height Jeep Libertys. They are a very...
Apr 16, 2025
WWDiesel
replied to the thread
Rear Upper Control Arm (Boomerang)
.
IronRock super heavy duty rear control arms are a permanent solution, never have to replace the boomerang again or the two lower control...
Apr 15, 2025
WWDiesel
replied to the thread
2004 Jeep Liberty Rear End Issue
.
Check your front control arms, could be one of them worn out.
Mar 17, 2025
WWDiesel
replied to the thread
06 liberty won't start
.
If you jump out starter relay pins #30 & #87 and starter motor cranks the engine, then most likely you have a bad starter relay or it is...
Mar 17, 2025
WWDiesel
reacted to
KJowner's post
in the thread
06 liberty won't start
with
Like
.
Might be a dying starter solenoid, time to get the multi meter out and see if the key is putting a supply to the solenoid.
Mar 17, 2025
WWDiesel
reacted to
KJowner's post
in the thread
Charging issue
with
Like
.
Yes, the alternator field is controlled by the ECU, you should only fit the correct alternator for the Jeep. If you have bought the...
Mar 17, 2025
WWDiesel
replied to the thread
intermittent P0300 on my 2005 CRD
.
Most likely you have air in fuel problems. If you have a leak on the OEM vacuum fuel system anywhere, it will suck air in, not leak fuel...
Mar 17, 2025
WWDiesel
reacted to
seafish's post
in the thread
intermittent P0300 on my 2005 CRD
with
Like
.
Time for the in Dodge Ram in tank pump upgrade?
Mar 17, 2025
WWDiesel
reacted to
KJowner's post
in the thread
intermittent P0300 on my 2005 CRD
with
Like
.
Air in the fuel system I'd guess.
Mar 17, 2025
Loading…
Loading…
Random media
Latest posts
Rusted E16 external torx bolts for wheel bearing.
Latest: KJowner
17 minutes ago
KJ General Discussion
What are my locker options currently for an 03 with SelecTrac?
Latest: KJowner
28 minutes ago
KJ General Discussion
Front LCA bushings replacement
Latest: KJowner
31 minutes ago
KJ General Discussion
Replacing rack and pinion bushings w/o removing it
Latest: KJowner
40 minutes ago
KJ General Discussion
What can you cut out of interior without comprimising unibody?
Latest: KJowner
42 minutes ago
KJ General Discussion
Members online
No members online now.
Members
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top