Search results

Ok 2005 3.7L. Bought used a couple of years ago. AC didn't work and I could smell coolant in the truck. Replaced everything on AC system (All parts new) and heater core. Evacuated and recharged AC system worked fantastic. Within a couple of months, AC stopped getting cold. Attached gauges...

I know this is an old thread but I have a question, what PCV valve (part #) are you putting in place of the crank case breather fitting in the back left of the motor?

You will most likely need to trace the wires from the turn signal into the vehicle. It was probably cut somewhere during the collision. Reconnect the splice color for color and make sure to cover and seal any bare wires.

Thanks for the answers gang! I did a whole bunch of degreasing to try and find the leak and I'm not sure now its from the PS pump or lines. I've also checked the fluid level a couple of times and its stayed the same so I'm kind of still looking. With all the cleaning I'm thinking maybe its an...

Hey gang, noticed some leaking on the garage floor and followed it to the Power Steering. I'm thinking its either the reservoir or the pump, can't tell with it on so I pan on pulling it off to see for sure. Is there a replacement gasket to go between the reservoir on the pump? Part#...anyone...

I just followed the body lines on the hood, pretty easy. Thanks though for the compliments.

I did not precut the vinyl for hood wrap. It's actually quite easy to do. You'll need some knifeless cutting tape. Clean your surface where you'll be wrapping, and apply the knifeless tape in your design, make sure the knifeless tape is sticks out so you can start it. Also if you are not...

Thanks! The Dash isn't all that hard if you take your time and be patient. I'd suggest taking pictures along the way and marking screws. Just think of all the money you save doing it yourself too.

With the seat skins washed and clean I can now reassemble my two front seats and add my seat heaters. Started with one of the seat backs. Back together. Now for the bottom. Add the cover. Then its time to assemble the seat and add the wiring for the seat heaters. All nice and tidy...

Once the dash was all back together, I took the opportunity to pull the carpet out to replace it. I ordered a replacement carpet kit which arrived and was the wrong color. Argh! It also was not at all what I expected, no padding, the molding was not right and lots of other issues. So I sent...

Ironically this is a good time to change sparkplugs too. Since you've pulled the coolant overflow you can get to the 2 rear plugs on the passenger side. With the Heater Core out You'll need to take out a ton of screws to separate it into two halves. Take the time to clean the inside out...

So some of you remember that I noticed after I fixed the AC that I had a smell of Antifreeze when running the heat in the Liberty. I also occasionally got a steamed up windshield. Well these are the signs of a bad heater core. This is not a fun job to do since you have to pull the dash pretty...

Ok so its been a bit since I gave an update. So I recently added the factory Tow hooks to the front. If you haven't done this, its not real hard to do it just requires you to pull off the front bumper cover. So after the cover is off you'll need to remove these boxes in the image below...

Thanks for all the help gang. Got it figured out! YEAH! The links above were great! I also stumbled across this old thread too: HOW TO: Install Steeringwheel radio controls on your Liberty | Jeep KJ and KK Liberty Forum So let me answer my questions from above: What did I actually need...

Just have some quick questions. Luckily I was at my buddy's Junkyard today looking for a couple of Visor clips and I ran into a 2002 Liberty Limited that had the steering wheel audio controls. I decided to pull the following: Rear Housing trim Left & Right Audio Buttons Harness Both Cruise...

Well Thanks for all the help. Come to find out they forgot to tighten some stuff down and the sales lady didn't know it wasn't done when it was let go. Luckily nothing happened, and I caught it was odd immediately. All fixed and no rub and she drives beautifully!

Yes, and Yes installed new OEM Replacement UCA's with all new bushings and Ball Joints. Set the bushing tension on the UCA and LCA once the weight was on the ground.

Ok so I know on the TJ's that there was a bolt on the Spindle that I could add a washer too, which would limit the turn in of the wheel. To eliminate rubbing. Does this exist on the KJ spindle or somewhere else? Just got the suspension finalized and had it aligned with some new tires wound up...

SO.... Tire question.. I'm thinking on going with set of Kumho Road Venture AT51 - in P245/75R16 or should I opt for the P265/70R16 I realize the main difference is a bit more width here with the 265. Thoughts? It's a shame I just can't stuff some SS TSL 34X9/16's up under her. lol So I...

Yeah, I spent the weekend tearing down the front end and fitting the spacers. Didn't like the way they fit and how they over extend and stress the front end. So they didn't go on. I also had to order Upper and Lower Ball joints and decided to just order replacement control arms with all new...