Search results

  1. P

    Trans cooler lines top line tranny side

    Prop shaft is already out. The line is in the fitting but I cant get it to sit down into it
  2. P

    Trans cooler lines top line tranny side

    I cant for the life of me get this line in. I got new transmission cooling lines because my old ones were leaking. Ive got all 3 of the other ends in the quick connects but the upper line (cold return?) on the transmission side just wont go in. Is there a trick to this? 07 kj 3.7L 42RLE
  3. P

    Power mirror triggers door ajar chime

    Nope. Door chime only happens if all apply: key in, door open, and a power mirror button pressed. Its almost as if the door ajar circuit is be completed by the power mirror switch.
  4. P

    Power mirror triggers door ajar chime

    Also, I have a service manual for a 2006. The wire colors dont match but Im hoping the connection diagrams are correct
  5. P

    Power mirror triggers door ajar chime

    With the door open, if I press any direction on the power mirror switch regardless of L or R orientation, it triggers the door ajar with key in chime. The chime does not go off otherwise. And this does not happen with the door closed. The switch does not operate the mirrors. The mirrors function...
  6. P

    2.5" lift. JBA UCA no cotter pin hole

    Ummm Im not sure if the ball joint is rebuildable. But it definitely wouldnt be hard to replace the balljoint. I got the one with the ball joint held in by those 4 bolts at the top
  7. P

    Drivers side uca

    Im under the jeep right now. I can reach the nut. Just cant get any leverage to break it free. That and idk how I would torque it back after im finished
  8. P

    Drivers side uca

    Ive got a 07 kj. Lifted 2.5 inches. Putting on JBAs UCAs. Drivers side rear bolt. How on earth do I reach it. The ABS module is in the way and I dont have enough extensions to bring the ratchet to the front. Can I take the ABS out without an issue?
  9. P

    2.5" lift. JBA UCA no cotter pin hole

    Also another quick question... how do I torque off the ball joint nut. I have to hold qith a wrench to keep the ball joint from turning so how do I click it off?
  10. P

    2.5" lift. JBA UCA no cotter pin hole

    Installing my new UCAs from JBA. And I just noticed there is no hole for a cotter pin on the ball joint. Old ones (not stock) didnt have them either. Is it just the lowers that have cotter pins?
  11. P

    Suspension bolt not threaded 100%

    Sooo to replace the clevis and the bolt/nut I'd need a spring compressor right?
  12. P

    Suspension bolt not threaded 100%

    Here is both sides. If I turn one side the other turns with it. So that kinda makes me think that it is crossed. That and it wouldnt budge even with over 100 ft lbs of force on it. I had the lift put on at a garage about a year ago. Along with control arms. So they caused it. Since it is so...
  13. P

    Suspension bolt not threaded 100%

    So I got the libby up on stands, planning to do the hubs. And I notice the bolt holding the (strut fork?) To the lower control arm isnt flush like the other side. Ive tried tightening it but it wont budge. Even past 100 ft lbs from my torque wrench. I dont have pneumatics or power tools...
  14. P

    How To: Change front driveshaft / change a driveshaft head

    Cant get new boot over splines I cant seem to slide the new boot on as simply as the post seemed to make it. Any tips?
  15. P

    Wire through fuse panel

    I think whenever I do electrical Ill just disconnect the battery all together. Just to be safe. But thanks for the links Renegade. Ill take a look and make out a plan
  16. P

    Wire through fuse panel

    Where can I het the things i need to do this? Did you use an actual PDC from a libby or electronics store
  17. P

    Wire through fuse panel

    Renegade - do you have a walk through for this? With pictures and stuff. That'd be helpful. Im nervous dealing with car electrical. I like the sound of that idea alot
  18. P

    Wire through fuse panel

    Hey guys, here soon I'm getting some interior lights for my 07 Libby. I want to wire them through a toggle and through the fuse panel or power distribution center so they wont be on if the key isnt in. just in case I forget to turn the toggle off. How do I wire something cleanly into an empty...
  19. P

    Lift faq: Read before asking questions!

    Thanks for clearin all that up y'all. I'm thinkin I'll just go with the Tommudd 3.5 lift on JBA. Seems much easier. I'm guessing that's yours Tommudd? lol
  20. P

    Lift faq: Read before asking questions!

    Alright. Read through all this. Still have a few questions. First, in regards to my previous question, do you mean that JBA says they give 1.5" but in reality they give 2.25 and 2.5? Second, what is UCA? Third, what is an ISO? And am I correct to assume that it gives a little lift? If so...

Random media

Noticed a lot of buggy type things on my radiator, and wanted a cool looking way to keep them out so I added some black aluminum mesh grill from ebay
image
16
The label
4943.jpg
finished side
15
2012 03 20 08 03 34 865
My first Jeep!

Latest posts

Members online

No members online now.
Total: 369 (members: 0, guests: 369)
Top