Search results

  1. K

    Went on a shakedown...got some issues

    Guess I need to know if the housings are the same. If not can I use it as I have it installed or do I need different mounts or axles? Do I need to take it apart and put the gears and DTT in my old housing?
  2. K

    Went on a shakedown...got some issues

    I have new housing out of a 4 cylinder, new 3.7 CV axles but the mounts are the same.
  3. K

    Went on a shakedown...got some issues

    I got a bare unit without mounts. Are the 2 housings different? I thought just the mounts were different and the housings were the same.
  4. K

    Went on a shakedown...got some issues

    No I used the same mounts...the diff bolted up with no problems and yea the right side looks good. I ran it with the front off the ground and the left has wobble..does not look right but the wheel does turn.
  5. K

    Went on a shakedown...got some issues

    Not a great pic but the left side axle at the diff.
  6. K

    Went on a shakedown...got some issues

    I do have a entire front axle out of a 4 cylinder. I also have a rear so both gears are now 4.10's. The rear is working fine but I'm havening issues with the front. The left side axle looks like its not far enough inside the differential. Its either the wrong axle or I didn't get it installed...
  7. K

    Went on a shakedown...got some issues

    I should not have to be using 4 cylinder axles correct?
  8. K

    Went on a shakedown...got some issues

    The front driveshaft turns.
  9. K

    Went on a shakedown...got some issues

    Mine is out at least 2 inches.
  10. K

    Went on a shakedown...got some issues

    On the ground it its whining and a slight grind but it will not pull off.
  11. K

    Went on a shakedown...got some issues

    The part numbers for both axles on the 4 cylinder and 3.7 are different.
  12. K

    Went on a shakedown...got some issues

    No Tom the right side looks good. Its the driver side that does not look right. Should that axle go all the way in flush with the differential? I got new axles from NAPA.
  13. K

    Went on a shakedown...got some issues

    Ok something is not right about the left side axle. Should the big part of the housing be flush with the differential? When its lifted it looks like its way to far out and the inner joint is in a pretty bad bind. But when weight is on the suspension the axle is straight but it does not look like...
  14. K

    Went on a shakedown...got some issues

    I call Eaton and pretty much a DTT would have to be hand grenaded to not work. So something somewhere is stripped.
  15. K

    Went on a shakedown...got some issues

    The front DTT is not pulling under a load. If you jack it up the driveshaft truns with the wheel but if you jack just the rear end up and put it in part time 4wd the driveshaft turns but the differential is just making noise and slightly pulling. And ideas as to what"s going on with the DTT? The...
  16. K

    Went on a shakedown...got some issues

    Any ideas on how to isolate what's going on? Some kind of front driveshaft issue? What is strange is the only thing happening when its in full time is that the front drive shaft is turning and making noise. Shimmed wrong? Bad locker..I did but it used but acutally it looked like it hand never...
  17. K

    Went on a shakedown...got some issues

    Well I just changed the front diff. I think that's my problem. The front driveshaft is spinning in full time 4wd and nothing else is happening. That's got me really confused because in part time the front is engaged and pulling. That should not even be possible.
  18. K

    Went on a shakedown...got some issues

    I am getting noise in full time 4wd and it barely pulls. Will pull for a stort stretch but then stops. I did a whole section in part time and once it slipped into not pulling. Has to stop put it 2wd and back into part time. Its a grinding noise but not a deep or loud noise. More like a whine.
  19. K

    Door lock crazy

    Is the fob working the rear glass?
  20. K

    My driver side seat

    So its tight at the pillar. The back does look wider than the stock seat.

Random media

After Second Wash
n541867197 815744 5338
sparkplug
5658.jpg
Interior
clip closeup
P1010075
052
P1000824

Latest posts

Staff online

Members online

Total: 417 (members: 4, guests: 413)
Top