Search results
-
O2 Help
is there a way to check the 02 connector with a volt meter before you replace the 02 sensor?- J33Pfan
- Post #9
- Forum: KJ General Discussion
-
Serious drop in gas mileage.
ive used a guy a few times already. Awesome service! its not just cleaning or guess cleaned. They measure the output before & after. give you a print out so you can see what the problem was. replace screens & o-rings etc. its a rebuild not a wash. $10 - $12 each- J33Pfan
- Post #26
- Forum: KJ General Discussion
-
2002 Jeep kj stalling problem
i never heard a FP causing a rich condition. sounds more like Fuel Injectors 1,2,6 might be black again. but a compression test first. anyways what type of spark plug you use makes a big difference! what did you install? it should be a copper plug or V-grove.- J33Pfan
- Post #6
- Forum: KJ General Discussion
-
Serious rubbing / noises off-roading
do you have all coil Spring Isolators installed?- J33Pfan
- Post #11
- Forum: KJ General Discussion
-
2002 Jeep kj stalling problem
how many miles and did it ever overheat? P030_ (1-6) is either a spark lug, Coil, or fuel injector. get back to basics! install new copper plugs like it says on the hood. Gap is .040. (if you use a different plug you might be in hell for a while) is there any liquid around the spark plug or...- J33Pfan
- Post #4
- Forum: KJ General Discussion
-
Serious drop in gas mileage.
i own the $100 unit https://www.amazon.com/OTC-3208-Enhanced-Engine-Transmission/dp/B0176W045U/ref=pd_lpo_263_lp_t_4?_encoding=UTF8&psc=1&refRID=DV3TVBGEX192F3JDMPM3 if you spray starter fluid around the hoses & intake parts you can find an vacuum leak. just dont be in a hurry and dont set the...- J33Pfan
- Post #21
- Forum: KJ General Discussion
-
Serious drop in gas mileage.
* if you can do your own work, take out your Fuel Injectors and sent them to a guy on Ebay to be rebuilt. you should have them back 2 - 3 days. are you running different tires? did you lift it? winter fuels here on the East Coast are terrible for gas mileage. What octane are you using? oh...- J33Pfan
- Post #9
- Forum: KJ General Discussion
-
2006 Jeep Liberty A/C problem
since it worked good before the pin damage, sounds like they didnt put enough Freon in it as mentioned, the dryer and the orifice might need to be replaced. if your system was emptied out, this should have been thought about since the system was empty -as a maintenance procedure. or was it...- J33Pfan
- Post #11
- Forum: KJ General Discussion
-
Prop shaft
Shouldn't be any movement. You found the problem.- J33Pfan
- Post #15
- Forum: KJ General Discussion
-
Rust repair?
fix it and sell it for $4500 like they do in NYC lol- J33Pfan
- Post #3
- Forum: KJ General Discussion
-
Coolant leak
do you have any puddles? if not could be a head gasket. auto stores lend tools. get the coolant pressure tester. dont over do it with the pressure. you have to use one of the universal ends. also -looks like you fan belt needs replacement- J33Pfan
- Post #8
- Forum: KJ General Discussion
-
Skid Plate Part Numbers
google search results for skid plates :gr_grin:- J33Pfan
- Post #30
- Forum: KJ General Discussion
-
New/aftermarket Bumper?
aftermarket bumper are usually less flexible then the OEM. they fit and go on, but the quality is not there. but you save a lot of $$. I would buy them -as a bumper can get damaged quickly. It wont hurt so much if a cheap bumper get damaged. but if you can sell the old bumper, it makes it...- J33Pfan
- Post #7
- Forum: KJ General Discussion
-
-
Smokin
If there is a head gasket leak, you could see many codes due to the ECM not being able to deal with water in the cylinders. either do a cylinder leak test or have a mechanic do it. You said you overheated it once. you dont know if the prior owner did the same. These heads will warp. IF...- J33Pfan
- Post #12
- Forum: KJ General Discussion
-
Prop shaft
could be the vibration caused the mount failure or its just age worn. how many miles on you jeep? did you check the front wheel bearings & axle shafts/ CV's.- J33Pfan
- Post #12
- Forum: KJ General Discussion
-
-
What's that smell?
Felpro also has the peanut gasket for the oil fill tube- J33Pfan
- Post #14
- Forum: KJ General Discussion
-
-
Working on rear uca
ok Ive seen a lot of high lift trucks. I thought the pinion angle was supposed to follow the driveshaft angle ... like in the "WRONG" picture :Insane:- J33Pfan
- Post #10
- Forum: KJ General Discussion
