Search results
-
What did you do to your jeep today?
this site wont let me upload pics anymore but heres the thread with toms pics, mine are the same, coming out of the side of the airbox and our to behind the grill http://www.jeepkj.com/forum/f202/cold-air-ram-air-intake-using-stock-air-box-59600/index2.html- krisP
- Post #12,943
- Forum: KJ General Discussion
-
What did you do to your jeep today?
i did this too if you want pics, pretty self explanatory though- krisP
- Post #12,941
- Forum: KJ General Discussion
-
What did you do to your jeep today?
enjoyed the freakishly nice weather- krisP
- Post #12,907
- Forum: KJ General Discussion
-
CV, front , length
i had both side by side and used a tape and they were different as well as quite noticably different....even the remand was a tad different from the stock that was in there d/t wear and miles of compression side note if anyone replaces that bearing/plastic bushing id recommend using the metal...- krisP
- Post #13
- Forum: KJ General Discussion
-
CV, front , length
imo if you are far enough to have the cv out you might as well replace the int. shaft or at least have one on hand...same for the seals and replace that plastic 'bearing' with a metal needle bearing. Some people say they are a huge PITA but they didnt give me any problems, plus that plastic...- krisP
- Post #11
- Forum: KJ General Discussion
-
What did you do to your jeep today?
drove back to erie from cleveland ... saw a nice lifted KJ on the way and WJ.... and more police on the highway than i thought possible haha- krisP
- Post #12,894
- Forum: KJ General Discussion
-
CV, front , length
i just put in a napa reman the other day after recieving the wrong "new" passenger cv.....remand was noticably better and much cheaper....and correct length- krisP
- Post #8
- Forum: KJ General Discussion
-
Front axle seals. Super stumped...
its a rubber bushing after 03 but can be replaced with the metal bearing...and what they show is the passenger and driver seals and bearings , they way they make the diagram seems like its an inner seal and bearing but its actualy representing the driver side. I got confused on that too at first -
-
Front axle seals. Super stumped...
haha now im confused too.... i coulndt find any part numbers or diagrams with inner front diff seals, ill look more later because now im curious -
Brake line extension
oops sorry, should have read your sig. Even at around 4 inch lift ive never had trouble with the break lines even when fully flexed , although i plan on the extended ss ones just because theyre nice- krisP
- Post #6
- Forum: KJ General Discussion
-
Rear UCA is shot, help!
here https://www.moparpartsoverstock.com/p/__/SCREW-Mounting--Upper-Hex-Flange-Head-M12x175x117-Control-Arm-to-Body--Control-Arm-to-Body-Mounting--Rear-Upper-Control-Arm-to-Body--UCA-to-Axle-Body-/6912159/06504748.html and here SCREW. Mounting, Upper. Hex Flange Head. M12x1.75x117 for Jeep...- krisP
- Post #71
- Forum: KJ General Discussion
-
Front axle seals. Super stumped...
http://www.colorado4wheel.com/manuals/Jeep/KJ/2006-KJ-SM.pdf here starting at page 149 , only the outter axle seals driver and passenger side, no inner seals like a full length solid axle -
Brake line extension
yep make a bracket for a couple bucks that drops down the brake line ... search google or here for break line relocation bracket- krisP
- Post #2
- Forum: KJ General Discussion
-
Front axle seals. Super stumped...
no you remove and install from the outside , passenger is the same its just recessed a few inches , i used a seal puller/pick like the one mentioned above....the factory service manual calls for a special tool that is basically a slide hammer Index of /manuals/Jeep/KJ there is the facotry... -
What did you do to your jeep today?
ordered my Miller 211 ..... not something done to my jeep, but certainly for it- krisP
- Post #12,856
- Forum: KJ General Discussion
-
Front axle seals. Super stumped...
there are inner and outer axle seals 566066AA is the mopar number , and AB for the bearing behind the outter axle seals...i also have an 07 and they use a plastic bearing/bushing back there that id reccomend replacing with the crown 0566066AB metal bearing... -
What did you do to your jeep today?
sprayed all the salt and road grime off and felt helpless when i saw some rust spots coming in again....need to get under there and undercoat again its buggin me. Really needs a good wash/claybar/wax after this winter , also changed the oil and front diff oil- krisP
- Post #12,845
- Forum: KJ General Discussion
-
axle bearing/bushing ?
turns out my passenger side JBA UCA ball joint was loose, needed to put a washer there to tighten it up...it was torqued to spec with coder pin and never has given me problems til now.....still dont know how the noise/feeling i was getting was coming from that but ever since it was fixed no more...- krisP
- Post #18
- Forum: KJ General Discussion
-
What did you do to your jeep today?
not all 07s , just like the PCV valves are set up differently in later 07s.. same as KKs setup...gaint pain for me to change because of the massive wad of wires all taped up sitting on top of it- krisP
- Post #12,834
- Forum: KJ General Discussion
Members online
No members online now.