Search results

  1. J

    No Cruise Control

    ok so was sitting here watching Miami Vice (movie) and reading forum post and found one that said check the throttle body cables so during a commercial I grabbed a flashlight and sure enough the cruise cable was popped off. All credit to Dave and adamjam2 on this thread...
  2. J

    2003 jeep liberty sporty idle problem

    So why such a wide variation in pricing? I am seeing everything from $20-$120 for the IAC.
  3. J

    2003 jeep liberty sporty idle problem

    So why the wide variation in pricing on these IAC's? I am seeing everything from $20-$140.
  4. J

    2003 jeep liberty sporty idle problem

    I was looking at this video before looking at my own. Clearly not the same intake setup. https://www.youtube.com/watch?time_continue=41&v=wjiEAVI49eI
  5. J

    2003 jeep liberty sporty idle problem

    I don't know, you tell me.
  6. J

    2003 jeep liberty sporty idle problem

    I got a new(rebuilt) engine put in a few months ago and I've not been overly happy with the idle. The idle is somewhat rough, seems lower (RPMS) than it should be and uneven. For a new engine I also seem to have a bit more lag between stomping on the gas and when it kicks in. That being said...
  7. J

    Serpentine belt position

    Well went ahead and ran up to the dealership and grabbed one from them. I get a discount there so it was actually cheaper than Autozone and since they are all plastic the Mopar one is probably better than aftermarket. They were able to filter on my VIN to confirm it has the 76/90 pulleys but...
  8. J

    Serpentine belt position

    I just posted that apparently there are two sizes. So only one of the two pulleys is larger, 90mm. Without getting all dirty at work trying to measure such a small difference, how sure are we that the 02's used a 90mm? I really hate to go from metal to plastic but I'll be darn if I can find...
  9. J

    Serpentine belt position

    Where are you finding metal? Also seeing two sizes, 76mm and 90mm. I have no clue which I have with it sitting in a parking garage while at work. Not the easiest thing to just reach in a measure either at just 14mm difference. I assume the difference would require a different built which is...
  10. J

    Serpentine belt position

    So the mechanic already got back with me and said it is surely the tensioner assembly and to just replace it. That's fine however all the aftermarket parts I am finding are plastic vs. the OEM metal. I am really not interested in putting on a plastic pulley so anyone got a source for a real...
  11. J

    Serpentine belt position

    WAs 9pm when I was able to look in there with the sound actually going on so I have not pulled anything off and I'm not going to most likely. Going back to shop for them to check their own work. Belt is just a year old, all pulleys, tensioners, etc are original except for water pump and...
  12. J

    Serpentine belt position

    Me again. I had the engine replaced in my 02 less than two months ago and I have started getting an oddball rattle from the engine area. It is very hard to make it rattle as it does it mainly when in drive at a slow roll. I was able to get on an incline and with some help with the Jeep in drive...
  13. J

    Codes P0837 and P0838 how to clear

    ok so I have another thread about cruise control but I want to zero in on clearing these two codes, P0837 and P0838. These would point to a faulty transaxle sensor which I have replaced and all the Lo, Partime time lights work again as expected on the dash. I bought a Bluetooth code reader and...
  14. J

    No Cruise Control

    ok so I bought an OBD code reader, works well, but codes P0837 and P0838 do not show up in the listed fault codes and it says there are no codes to clear however those two codes do still show up doing the ignition switch 3x trick. So these codes are not stored in the ECM? Would these codes keep...
  15. J

    Help - Stuck in the Driveway

    It is. Is that where it is supposed to be ended?
  16. J

    No Cruise Control

    So the "vacuum hose" is probably the xfer case breather hose. I will have to check that end again but that would make sense as it has a body molding type of clip for attaching to a body panel. I am better they disconnected it when they changed my engine out last month. Any ideas where it is...
  17. J

    No Cruise Control

    As it was working fine that AM and not in the evening I don't think it was the steering column switches, just went out without any issues prior to that. So nobody thinks the error codes being thrown by the transfer case selector sensor would be the cause? I have that on order, actually the...
  18. J

    Help - Stuck in the Driveway

    ok success, Liberty is back in the garage. Was able to get the shifter cable back on the xfer case. I assume there is supposed to be a lock washer of some sort on there to keep it from popping off like that?
  19. J

    Help - Stuck in the Driveway

    ok I pulled the center console out to track down the problem, followed the shifter cable to the rear of the xfer case and it is disconnected. I can't move the selector on the xfer case and wondering if the sensor might be locked and applying enough force to keep me from being able to move it...
  20. J

    Help - Stuck in the Driveway

    Transfer case sensor was acting up so I decided to run the $ Wheel drive selector through the hi/lo while sitting in the driveway. Well after putting it back into 2 Wheel drive I am stuck. No matter what gear I put the Jeep into it is stuck. Put it in neutral and selector in neutral and even on...

Random media

Bagshot no 8
IMG 1098
2004 Jeep Liberty Sport 4WD - Dealer Photo 1.7
20250227_094755.jpg
Kayak Trip with the new rims
image
jeep2
404223 10150618393250362 663880361 11087486 1791822603 n
IMAG0086

Latest posts

Members online

Total: 548 (members: 2, guests: 546)
Top