Recent content by JeepinSteve
-
Fuel Injector Recommendations
Hello Jim. Thanks for the info. I went to Bosch's website. It looks like the only sell re-manufactured injectors for Diesel motors. Below is the link if anyone with a diesel is looking for this service. I will give them a call tomorrow to see if they have a similar service for gas...- JeepinSteve
- Post #3
- Forum: KJ General Discussion
-
Fuel Injector Recommendations
Hello All. I have a 2004 3.7 Jeep Liberty. I would like to replace the fuel injectors as they have over 245k miles. I typically like replacing parts using Mopar parts if it makes sense based on the price. In this case, the injectors are just way to expense considering I will need to buy six...- JeepinSteve
- Thread
- Replies: 4
- Forum: KJ General Discussion
-
Winch mount on stock bumper.
There is a small amount of sag from adding the winch and of course what you would expect over time. Nothing that is to concerning. I’m not sure the measurements from before the winch, but I measured the front and rear today. The front is 21” from the center of the wheel to the bottom of the...- JeepinSteve
- Post #43
- Forum: How To
-
Winch mount on stock bumper.
Hello JustSumDad. So I have never had to use the winch to this point as I have never been stuck. The mud tires (Cooper STT Pro) and the Detroit TruTrac have worked very well so far. It’s no secret that the mounting points on the Liberty uniframe are not very thick. With that said, the winch...- JeepinSteve
- Post #39
- Forum: How To
-
Stripped belt tensioner bolt ?
I had the same issue when removing my tensioner. The bolt immediately rounded out. I tried everything to get it off. I ended up drilling the head of the bolt. Once the head of the bolt fell off, the tensioner fell off the motor and I was able to unscrew the bolt by hand. Hope the works for you.- JeepinSteve
- Post #17
- Forum: KJ General Discussion
-
Deeke's upper control arms?
Good luck. Looking forward to hearing how it goes.- JeepinSteve
- Post #26
- Forum: Lift Kit Discussion
-
Deeke's upper control arms?
Just from your experience installing these control arms, do you think it would help to get bushings with a thicker outer lip so you could eliminate the metal washers? Basically the outer portion of the bushing would be thicker thank the original bushing thus no need for the metal washer. Hope...- JeepinSteve
- Post #23
- Forum: Lift Kit Discussion
-
Deeke's upper control arms?
Hello Stu. I have not had an opportunity to install them yet. What is the problem you are having installing them? Does the inner metal sleeve fit in the opening without the washers? On the Amazon listing for these control arms, there was a comment/Review about the washers being to big to fit...- JeepinSteve
- Post #21
- Forum: Lift Kit Discussion
-
Deeke's upper control arms?
Thanks for the update. I also bought a pair, but have not installed them yet. The quality looks good, I don't see any issues with them either. It's good to know they are working good for you. Did you need to install the metal washers between the frame and the poly bushings? Any closeup...- JeepinSteve
- Post #17
- Forum: Lift Kit Discussion
-
Fuse for rear passenger windows?
Hey Desertdriver. Did you ever figure out what was the cause of the rear windows not working? I'm having the same issue. The fronts work fine, nothing in the rear. I haven't started the diagnose process yet. Any info would be great. Thanks.- JeepinSteve
- Post #7
- Forum: KJ General Discussion
-
Jeep Kj Offroad
Here's a link to a guy that installed them on his KJ. https://www.jeepkj.com/threads/deekes-upper-control-arms.80370/post-814218- JeepinSteve
- Post #10
- Forum: KK General Discussion
-
Deeke's upper control arms?
I found a video on Youtube of a guy doing a budget build on a 2003 Jeep liberty. If you forward to 9:10, he puts Deeke upper control arms on the jeep and mentions in the video that they have been perfect so far. Anyone else try them?- JeepinSteve
- Post #13
- Forum: Lift Kit Discussion
-
best replacement when rebuilding the suspsension
I installed OME front and rear. Jeep rides great with no suspension issues. Here are some pics of the lift. https://www.jeepkj.com/threads/ome-suspension-lift-and-tires.78690/post-792134- JeepinSteve
- Post #6
- Forum: Lift Kit Discussion
-
07 radiator and cooling issues.
Did you bleed the system after replacing the radiator? There's a bleed screw on the upper coolant hose housing. Just google the process of bleeding the system. Hope that helps.- JeepinSteve
- Post #2
- Forum: KJ General Discussion
-
2004 Drivers side leak from fire wall wire harness?
Hello. My 2004 Liberty is leaking from the firewall wiring harness on the drivers side just to the left of the clutch pedal as you can see in the picture. I put a hose to the bottom of the windshield and I could see the water flowing in. I know that wiring harness comes in from the engine bay...- JeepinSteve
- Thread
- Replies: 2
- Forum: KJ General Discussion
