Automatic P-R-N-D-2-1 (bulb type)

[Trodo]

Okay, down where you pick the gear, what's the bulb type and where is it in the lower center area?

 

[Gentleman]

(1) Remove the shift bezel, if equipped.
(2) Set park brake lever in the up position.
(3) Using a trim stick C-4755 or equivalent, disconnect
the manual trans shifter boot, if equipped.
(4) Using a trim stick C-4755 or equivalent, disconnect
the transfer case shifter boot, if equipped.
(5) Remove the four bolts. (Fig. 3)
(6) Lift the console at the back and remove.


(1) Disconnect and isolate the battery negative
cable.
(2) Remove the center console from the floor panel
transmission tunnel.
(3) From the left side of the vehicle, reach between
the transmission range indicator and the floor panel
transmission tunnel to access the illumination lamp
socket
(4) Rotate the socket counterclockwise about 30
degrees to unlock it from the bottom of the range
indicator.
(5) Pull the socket and bulb straight out of the
keyed opening in the range indicator.
(6) Pull the bulb straight out of the socket.

(1) Align the base of the bulb with the transmission
range indicator illumination lamp socket.
(2) Push the bulb straight into the socket until the
base is firmly seated.
(3) Align the lamp socket and bulb with the keyed
opening on the bottom of the indicator (Fig. 12).
(4) Insert the socket and bulb straight into the
bottom of the indicator until the socket is firmly
seated.
(5) Rotate the socket clockwise about 30 degrees to
lock it into place.
(6) Reinstall the center console onto the floor panel
transmission tunnel. (Refer to 23 - BODY/INTERIOR/
FLOOR CONSOLE - INSTALLATION).
(7) Reconnect the battery negative cable.

The Fsm does not specify the bulb type

Bob

 

[Trodo]

Thanks.
Half way there.

 

[Havoline]

Sounds as if it might be easier to just use a flashlight to see which gear you're in! drunk.gif

 

[KevinJBell001]

(1) Remove the shift bezel, if equipped.
(2) Set park brake lever in the up position.
(3) Using a trim stick C-4755 or equivalent, disconnect
the manual trans shifter boot, if equipped.
(4) Using a trim stick C-4755 or equivalent, disconnect
the transfer case shifter boot, if equipped.
(5) Remove the four bolts. (Fig. 3)
(6) Lift the console at the back and remove.


(1) Disconnect and isolate the battery negative
cable.
(2) Remove the center console from the floor panel
transmission tunnel.
(3) From the left side of the vehicle, reach between
the transmission range indicator and the floor panel
transmission tunnel to access the illumination lamp
socket
(4) Rotate the socket counterclockwise about 30
degrees to unlock it from the bottom of the range
indicator.
(5) Pull the socket and bulb straight out of the
keyed opening in the range indicator.
(6) Pull the bulb straight out of the socket.

(1) Align the base of the bulb with the transmission
range indicator illumination lamp socket.
(2) Push the bulb straight into the socket until the
base is firmly seated.
(3) Align the lamp socket and bulb with the keyed
opening on the bottom of the indicator (Fig. 12).
(4) Insert the socket and bulb straight into the
bottom of the indicator until the socket is firmly
seated.
(5) Rotate the socket clockwise about 30 degrees to
lock it into place.
(6) Reinstall the center console onto the floor panel
transmission tunnel. (Refer to 23 - BODY/INTERIOR/
FLOOR CONSOLE - INSTALLATION).
(7) Reconnect the battery negative cable.

The Fsm does not specify the bulb type

Bob

Is this the same procedure to align the orange gear indicator? Mine is loose.