What did you do to your jeep today?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

seafish

Full Access Member
Joined
Jan 10, 2024
Messages
623
Reaction score
798
Guess I could just pull it off to check pulleys

An alternative is to (carefully) use a mechanics stethoscope or even a wooden dowel to listen for bearing noise or even the squeak at each pully

That said feeling for to much or not enough play at each pully is even better
 
Last edited:

burntkat

Full Access Member
Joined
Sep 14, 2021
Messages
512
Reaction score
378
was letting jeep run while i was chopping leaves with mower when i started heard a little chirp sound any one experience this before sounded by alternator por power sterring pump area not sure how if possible to post lik vid here i let it run gave it some throttle and it did go away
You'd have more success if you didn't write everything as a runon sentence. Not being pedantic, I just don't have time to translate.
 

LFX1

Full Access Member
Joined
Jan 11, 2024
Messages
142
Reaction score
93
An alternative is to (carefully) use a mechanics stethoscope or even a wooden dowel to listen for bearing noise or even the squeak at each pully

That said feeling for to much or not enough play at each pully is even better
Yeah, funny you should say this, my dad always does this with a wood handle of an old broom I just didn't have anything.
 

lfhoward

Wheel. Repair. Repeat.
KJ Supporting Member
Joined
Dec 9, 2012
Messages
3,012
Reaction score
3,510
Location
Philadelphia, PA
Got a P2098 code running on the highway at 65 mph today. No noticeable change in engine behavior, but apparently a lean condition in bank 2. This could be old weak fuel injectors, a vacuum leak, an exhaust leak upstream of O2 sensor 2/2, or possibly bad wiring or a bad sensor (2/1 or 2/2). There’s a lot to sort out with this one.
 

NickJeepKJ

New Member
Joined
Feb 24, 2026
Messages
1
Reaction score
8
Fit a new wishbone to mine. Old one was tired. The ball joint kept on pushing out and the bush on the one side was completely shot. Also replaced the fan pulley and harmonic balancer. Eventually made the time to fit the snorkel i bought 8 months ago.
You must be registered for see images attach
 

burntkat

Full Access Member
Joined
Sep 14, 2021
Messages
512
Reaction score
378
Took the day off to adjust to the time change. Kid asked me to come out to his shop so we can swap out rhe CPS. While we have her up on the rack, checked out the wishbone joint at the axle again. Sure as shit, the poly bush is eaten up.
Called IRO and went through it with them... Asking what I might be doing wrong. Verified I'd torqued the joint properly. Took pics of the joint with my son's borescope, verifying the fasteners are present. Sure as hell, the poly is beat to death. Verified with the guy at IRO the joint should be greased twice a year... I used Lucas Red-n-Tacky, which is what they use. So there is nothing apparent that I am doing wrong.

IRO is sending a new joint out, gratis. Pretty good service! If this goes a third round, I may change over that whole joint (less the welded bracket assembly) to something like a Rubicon Express joint. Any recommends on the best HD rock crawling joint out there? I am thinking if it will take that kind of service it ought to take daily driving.

Also found out both brand new tires on the PAX side have screws in them. Much gnashing of teeth and swearing ensued....
 

burntkat

Full Access Member
Joined
Sep 14, 2021
Messages
512
Reaction score
378
Iron Rock Offroad.

Sorry, meant to post pics along with...

You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach


Everything about the install was Ricky-tick. I verified it all with the guy at IRO while I was on the phone... To the point I was basically asking him how to blame the issue on me. But no, I followed it all... (this time - first time was on me for not torquing rhe sideplate bolts properly - they departed and the joint fell apart, then the poly degraded and departed.) But no, as I said earlier, even verified the grease I was using - Lucas Red-n-Tacky. It's the same as they use. He volunteered to send me new sideplates, and when I inquired about peening of the ball joint itself (which was a problem last time, owing to the outer housing slamming into it) he upgraded it to an entire joint kit.

While I have this apart to replace, he needs lots of pictures for their R&D guys to pour over to see if they can figure out why it failed. Meanwhile, I will take micrometer readings and suss out the thread pitch of the threaded portion and source out a replacement in a Johnny Joint or similar. Third failure (in less than 5 years of street driving) will be the last time I use an IRO joint. (I have gone through 2 of these so far in something like 2 years - first failure was completely my fault).

He did verify Lucas Red-n-Tacky is the move on the grease front, and twice yearly greasing should be plenty (and be generous 'to the point of sloppy' with the grease)
 

burntkat

Full Access Member
Joined
Sep 14, 2021
Messages
512
Reaction score
378
Interesting info....

Here's the joint in question (PN 10670 on IRO's site) ...
You must be registered for see images attach


I noted the "HK 127" on the receipt and on the web page and figured that must be a PN for their supplier.... Sure enough, took me to this...


(EDIT - THIS LINK APPEARS TO BE A FAKE SITE ON FURTHER REVIEW. DO NOT PURCHASE FROM OR VISIT IT)

Now, looking at their site, the Pic is completely unrelated. But the Dims are the same. I believe this is a cheaper source for the same product.

It stands to note, they claim to be using UHWMP (ulra-high molecular weight polyurethane), but I don't believe its failure mode is chunking like I saw last time. That was a completely unrelated issue though - assembly failure on my part. This time, if I see chunking, I believe we have the issue sussed out. Theory is, their supplier is providing high-durometer rubber or polyurethane as opposed to UHWMP. If I can prove that, I will scan in their unmolested races and then see about 3d printing my own in UHWMP.

EDIT - Apparently UHMWPE is not suited to 3d printing, at least not with consumer systems. Also, IRO claims to machine their bushings in-house. I am going to buy one of these items from the joint above and see what arrives. Who wants to bet it's identical?
 
Last edited:

burntkat

Full Access Member
Joined
Sep 14, 2021
Messages
512
Reaction score
378
By no means am I badmouthing their products. They have been my second-string go-to people when I build Jeeps.... First being a tie Rubicon Express and Roughstuff Specialties (who went out of business on me).

Looking at the properties of UHMWPE, I see that it begins to fail and flow at relatively low temperature - 194F. Nylon would be a better solution there, from what I'm seeing.

... And I can print nylon... With some work. ;)

Or maybe I just wrap the hell out of the exhaust pipes (not sure how far away it is, but it passes in that vicinity, IIRC). Or maybe I suggest that they spin up a 'premium bushing for high heat locations'. Should not require much more effort than purchasing nylon round stock if they are truly machining these in-house.....
 

burntkat

Full Access Member
Joined
Sep 14, 2021
Messages
512
Reaction score
378
You must be registered for see images attach


See that exhaust pipe in the left corner? Something like 5 inches from the joint....

I wonder if it's getting the joint to 195F or so....

I ask because it appears, if the info I am finding is accurate, that UHMWPE starts to flow at 194F. This could be the entire problem.

I need to figure a way to rig a thermo probe for my meter there and run it inside the cabin to my Fluke meter, so I can get some in-service readings...

Hmmm... There must be some way to make a Bluetooth thermocouple module monitor this and report to my phone.... Anyone else geeky enough to offer input?
 
Last edited:

burntkat

Full Access Member
Joined
Sep 14, 2021
Messages
512
Reaction score
378
Drive it normally but carry around an IR thermometer and check the temp of the bushing at usual stops?

Alternatively, fashion a simple sheet metal shield to block some of the heat and see if the problem goes away.
I'm looking for data in real time. I have plans on how to address if it pans out while in service.
 

duderz7

Full Access Member
Joined
Jan 20, 2016
Messages
1,646
Reaction score
1,439
Location
Weiser, ID
A diff gets pretty hot too, and metal transfers heat. I'll have to look closer at mine. Every time I try to grease it seems so tight it won't take much grease
 

HIM610

army27y8m8d
Joined
Oct 25, 2026
Messages
5
Reaction score
4
Location
Mid-Atlantic USA
So contact cleaner, but is there any other spray we can use to protected it from any moisture?
Yes, there is. I don't know if you want to go there or not.
The circuit boards on spacecraft are covered with "conformal coating" that protects the circuit board and all of its components from contaminants on earth and in space.
I don't know what it costs for a board to be conformal coated, and it is a hassle if one of the components on the board needs to be replaced.
 

burntkat

Full Access Member
Joined
Sep 14, 2021
Messages
512
Reaction score
378
Last edited:
As an Amazon Associate we earn from qualifying purchases.

burntkat

Full Access Member
Joined
Sep 14, 2021
Messages
512
Reaction score
378
(quote)
So contact cleaner, but is there any other spray we can use to protected it from any moisture?
Yes, there is. I don't know if you want to go there or not.
The circuit boards on spacecraft are covered with "conformal coating" that protects the circuit board and all of its components from contaminants on earth and in space.
I don't know what it costs for a board to be conformal coated, and it is a hassle if one of the components on the board needs to be replaced
(/quote)

Not sure what he was referring to, but there are many options to waterproof electronics. Best approach if you can isolate the components in a small project enclosure is to epoxy-pot the assembly.

Granted, serviceability becomes MUCH more complex....
 

Members online

No members online now.
Top