Hello was wondering how to get the bushings for rear shocks 24-185660? Do i need to take them to a shop to have them taken out and pressed .im currently doing my rear lift. Thanks
Hello i would like to know which way are the two small peices of hardware should be facing while assembling the coil over set. I took everything to a shop and want to make sure its done correctly. Should the two pieces be hugging the strut bearing or should the lower washer be facing down in...
Im trying to remove the right passenger UCA and one of the bearings on the bushing has seized on the bolt. I cant remove it . I tried smacking the bolt out at least 100 times already. Its almost out but how am i suppose to loosen the rest of it. I cant get a dremel in there . Should i use a...
So i had the issue with no start no click and discovered a piece that chipped off on the pin. Couldn't find the piece but still messed with the switch and was able to turn on the engine with a flat head and fired right up. I will need a new actuator i ordered (Dorman brand) . As you can see in...
Hello , So i had an issue this week with the p0139. The stubborn 02 sensor was giving me problems. Scanned and reset twice. I drove on the fwy the second time with my scanner to make sure it wasn't pending. I then drove it to get smogged and it passed luckily. On top of that i have another...
Hello so I changed my front differential fluid today.
I was only able to get about a little under 2quarts until it started dripping out the filler plug. I even jacked up the passenger side to help put in more .
Is this enough?
Thanks
04 liberty auto/with command trac.
Hello was wondering if anyone could help with finding the correct Bump stops for Rear? Im getting ready to do the OME 948 set up for the rear. Do i use the factory ones and just add the “hockey puck”at the bottom? Any part numbers would help . Thanks
Hello i wanted to know . Do i need new upper strut mounts if i am planning to do the ome lift set up. Could i use the old ones or can i go with some aftermarket mounts like moog? Thanks
Hello im getting a rattle sound coming from drivers side underneath by the cat exhaust. I was thinking it might be my tensioner but the sound is in park or neutral. And when i raise the rpm up. it rattles up then goes away after i let off the gas. Then comes again . Could this be my exhaust as i...
So I accidentally deleted the post that i meant to edit . If you could reach back about the brake issue i had about going down hill on neutral with the engine off. Is it normal to have stiff braking? Thanks again
Hello i wanted to see if anyone tried to use this i found online . I was thinking of upgrading my front bumper on my 04 KJ but it is fabricated for 07+ Wrangler , JL, and JT. I like it and its cheaper than ARB . Can it be done? Any tips thanks!
Hello im noticing my exhaust smells burnt and smokes after idleing for very long. Could this be due to a rusty muffler. Could there be a leak coming out ahead of the muffler. Any tips? . Thanks
04 3.7l 148,000
This morning i turned on my kj and didnt warm up as i usually do . When i took off after about 30sec . Warm up my oil light illuminated then turned off. I kept driving a little more then it flashed more time. What could it be? Thanks
Hello has anyone used the infinity 6532ix cross reference speakers. I cannot find the 6032CF that most people have. I wanted to know if i could still do the same set up with the factory amplifier attached to the speakers at the door. . Any suggestions on some front speakers would help. I just...
Im getting my auto trans flushed by the dealer. Ive had the KJ V6 for 5 months now and want to see how the results will be. I have 144,000 miles i dont think the tranny has ever been serviced . Should i have gotten a fluid exchange or Just go with the flush?
Hello im having trouble with my KJ rear end . Its doing the (hula) also i see as im driving my rear wheels are driving side to side . I didn't realize it was the bad until i noticed the side to side movement . Is it my lower control arms and differential shaft? how would I check each one? I...
Help, Im having trouble getting the front lower control arm off. The cam bolts seem to be stuck with the inside of the bushings . Any suggestions. I tried a reciprocating saw but it doesn’t seem to work.
Hello i wanted to see if anyone had luck installing these type of lights. I wanted them for the front bumper. Possibly as DRL or spot lights. How would i wire them? They are “IJDMToy” 10w dual lights . Thanks
Hello everyone, has anyone ever tried using A/C Delco upper cylinder and fuel injector cleaner in there jeep to clean injectors/ valves. Ive used one time in my e46 . I read it can be done once in a while . I put about an ounce or 2 in every spark plugs cylinder (Squirt it in the hole) let it...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.