Search results

Installed maglite mounts. Now I just need to find my maglite haha Sent from my iPhone using Tapatalk

Found out one of the shocks in my pre-owned iron man struts I just got is worn out. Passenger side makes a good amount of noise over bumps. Guess that's what I get for trying to get by cheap. Time to pull them and swap in new shocks. [emoji1303] May just leave it, idk yet Sent from my iPhone...

Sorry for the late reply, phone notifications have been failing me lol On the front center of the hub to fender it's at 22" On the rear it's at 18.5" Sent from my iPhone using Tapatalk

These are pre-owned iron man coils and shocks so they should have settled by now to where I won't need another alignment for some time. It was just a time issue and I need it to be on the road as it is one of my daily drivers. The front ended up taking way longer then anticipated because...

Got the front lift on, off to get it aligned. Then need to figure out what route I want to take with the rear. Sent from my iPhone using Tapatalk

If shipping wasn't so expensive I would have taken them off your hands! Free bump Sent from my iPhone using Tapatalk

Easy job turned difficult due to lack of maintenance from previous owner. Take care of your rig people, or don't b**** to the mechanic when you get a high repair bill when you neglected the basics!!!! End rant... lol the humidity in Florida is getting to me Sent from my iPhone using Tapatalk

Cleaned up these bad boys before I throw them in [emoji57] Sent from my iPhone using Tapatalk

I'm at stock gearing with stock tires at the moment. lol I heard jeeps are somewhat sluggish but seems like way worse then normal. I had a 3.0 Vulcan V6 in my Ranger back in the day and that had more pull then this. It's not binding via a brake issue because that was my first thought as...

If i hammer the throttle (pedal to the floor) my jeep seems to make a lot of noise but barely pulls. Is this just a normal thing for the 3.7? It feels like I'm pulling a boat anchor or something. No codes are being thrown. Sent from my iPhone using Tapatalk

Nice! I've been in the market for some new shocks and coils because mine are shot. I'll keep an eye on this post when you get the pictures up [emoji1303] Sent from my iPhone using Tapatalk

What shocks are they paired with? Sent from my iPhone using Tapatalk

Fogged the skeeters around it Sent from my iPhone using Tapatalk

Thanks for the clarification. Just hate spending $65 on something so small [emoji58] Sent from my iPhone using Tapatalk

My sunroof switch has finally died and I need a new one for my 2004 Libby. When looking for a new switch I noticed that the switch that says it works for the 04 is $65 where you can pick a switch up for a 05-07 for only $15. What the heck! Lol So is the 05-07 the same connector as on the 04...

I was in Home Depot the other day and walked past the shower grab handle/bars. It made me think. Would a 30" stainless bar look good holding up some auxiliary lighting on the front bumper? Of course I would probably coat it black to mask that it is in fact a shower grab bar lol Unit in question...

I know I'm contributing to the off- topic subject but I have an air impact, full impact socket set and full tool kit made by DEWALT and they far outshine any other brands I have used. I once sold craftsman products for a living but I wouldn't waste any of my money on them. Not what they once...

Investigated a clunking noise I get on take off and during braking. I think it's the rear control arms so off to the parts store to get some new ones Sent from my iPhone using Tapatalk

I wouldn't trust that thing going off-road over some small yard bushes lol. The CVT or variable trans has solenoids in it and I guess those are known to fail so I'm looking in to it now. (Can't be too mad I guess it's over 200,000 miles) You are correct, I only had a 5 1/2 drop on it and I...

How did you like the Duratracs? Was thinking about going with those on mine. Sent from my iPhone using Tapatalk