Search results

Hello, I have a question about the rear differential on my KJ. The goal is to have a gear ratio equal to 4:11 and I found a complete rear differential with this ratio but it's a DANA 35 and not a Chrysler 8.25 as actually. Do you think it's a good idea ? Thank you for your help. Ludo

Dear all, I need to remove the front drive shaft on my Jeep KJ 3.7 to rebuild the CV joint on rear part, but it's impossible for me to remove it because the drive shaft is blocked by the exaust pipe on left side and the transfert case support. Can you help me please ? Thanks. Ludo

Hello everybody, I am looking for a Ring / Pinion kit with ratio equal to 4.10 for my JEEP KJ 2002 with DANA 30 front differential and Chrysler 8.25" rear differential. I live in France, but I can take over the transport costs. Thank you for your help. Best regards, Ludo

Hello, after few months with my 2.5" liftkit OME (927/948) and JBA A-ARM, I just installed full Skid plate DIY and Rock sliders DIY also. But, today I see that the front vehicle is lower. And the front left side is lower that front right side. Can you help me choose the modifications among...

Hello, I want to make a full flush of my automatic gearbox. So I need to disconnect the oil return hose (between the radiator and the gearbox). Can you tell me the location of this hose and if it is more practical to disconnect it on the radiator side or gearbox side? Thank you for your...

The question is simple: Can I install a second AC compressor to produce compressed air? If yes, I'd like to install it between the air box and the original air-conditioning compressor. Your opinions ?

Hello, I changes wheel to use a larger size: 245/75R16 And I would like to add 1 or 2 gasoline jerry can on each side of the spare wheel. Do you think the trunk and its stock fixings will support the weight of the new wheel and cans? Thank you for your help.

Hello everybody, I want to install a new tire on my KJ with 2.5" lift (245/75R16) and I was offered both choises : 1. Rim Triangular 7x16" with Offset = 30mm = 1.18" 2. Rim Triangular 8x16" with Offset = 0 What's the best choice ? Thank for your help.

Hello, I want to install a new tires on my KJ 2002 v6 3.7 with stock rim 16". Can you confirm me that 245/75R16 tire on stock rim with 2.5" lift is possible without issue ? Currently, I have stock gear 3.73. Is it possible to run everyday with 245/75R16 tires and 3.73 gear ? For...

Hello, following the replacement of the throttle position sensor on my KJ because the fault code P0122 was present. Now the fault code is no longer present but the acceleration is bad, not very nervous and also strange idle. According to the service manual, there's nothing special and...

Hello, The car just out of all alignment and here's the result: Camber left = 0.46 Camber right = 0.44 Caster left = 2.52 Caster right = 2.05 Para left = -0.05 Para right = -0.03 Do you think these settings are right? Thanks for your...

Hello, Arriving at the end of the installation of my réhausse 2.5 "JBA (OME 927/948), I find myself in a dilemma. How to properly tighten the steering ball joints on the pivot knuckle? According to the workshop manual the torque is 108 Nm. Problem, I'm screwed, my Torque wrench does not...

Hello, I will install a 2.5" OME lift kit (OME 927 / 948) with A-ARM JBA on my KJ 2002. But I still want to know which tires size to choose. I would like to use the 245/75R16 but I fear that the gear is not suitable. I want to absolutely keep driving pleasure on the road without changing...

HELP : Engine cut by driving Hello, I have a big problem on my Jeep KJ 2002 V 3.7. Sometimes, my engine cut off in driving on the road and I am forced to restart. The engine restart whithout any problems. I have just one error on OBD : P0122. I tried to replace the throttle position...

Dear all, Firstly, sorry for my bad english, but I'm french... Secondly, I am installing a OME lift kit from JBA with following parts: - OME kit pre-assembled (springs & shocks) 1.5" - JBA Upper Control Arm for lifted Jeep - Front Bumpstop Teraflex On this forum, I have read that it...