Search results

Are you replacing the "Timing" belt that drives the camshafts, or just the Serpentine/Accessory drive belt that runs around the water pump and alternator etc?

Hello Brad Do you still have your KJ? If so, did you sort out the brake issues? When our brakes started dragging, I rebuilt the front calipers with new pistons and seals. The rear calipers were flushed/cleaned out, but not yet rebuilt. I found that a "hard" pedal and "not much braking" was due...

Our local dealer refuses to service Cherokees that are more than ten years old.

Did you ever replace the engine accessory/serpentine belt?

Trying to cut the ends is a rough way to remove the CV shafts and my cause vibrations??? Disconnecting the lower ball joints etc will make a much better job.

I've come into this thread a bit late and am wondering why are you replacing the front diff?

I have just finished replacing the front propeller shaft on my 2007 KJ CRD. If you have a V6, then the exhaust joint probably has to be unbolted. This section from a Service Manual has the description headings reversed. The first section is actually showing the exhaust for the V6. Once the 6...

Is it the front propeller shaft that you refer to as the "intermediate shaft"?

I have a 2006/2007 KJ CRD LTD that we bought new and am finding that many of the parts required to keep it on the road are no longer available. The factory parts support seems to have started droppping off after ten years, in about 2018 and has gradually gotten harder to source parts. Rockauto...

Disabling the ESP helps driveability on faster dirt roads ...

....removed the front propeller shaft, to stop the vibrations caused by the output shaft bearings. I have a replacement Zumbrota unit, but am waiting for a new Transfer Case Yolk seal. https://www.zumbrotadrivetrain.com/catalogsearch/result/?q=242j-10

Have you ever replaced the ball joints in the lower control arm? Mine have failed previously and caused a noise like you mention. New ball joints eliminated the noise. I now have greaseable ball joints in the upper and lower control arms.

Did getting the transfer case removed and swapped/rebuilt fix your noises?

Our 2006/2007 KJ has CV joints on the front propeller shaft. The rear of the propeller shaft has a CV joint that regularly fails. As it bolts onto the front of the transfer case output shaft, it can damage the transfer case front output shaft bearings and cause oil leaks.

In "Full Time", the centre diff is unlocked, so if any wheel starts spinning, there is no drive to the three other wheels. In "Part Time" the centre diff is locked, and drive to front and back diffs is split about 40/60, so then you need one front and one rear wheel to start slipping before you...

What has caused the failure of your transfer case? My 2006/2007 KJ had a failed rear CV joint, and the "242 J" transfer case started making horrible metal/metal screeching noises when 4WD was engaged. I was in the middle of a remote trip, so had to keep driving it for about 3,000km to get to a...

I had similar issues, and ended up replacing all of the idler pulleys, the belt tensioner, and the alternator pulley. The alternator pulley has a self aligning, one way drive clutch built into it, so that the alternator can freewheel when the engine speed drops suddenly...

Have you got any information on the brand and specifications of your new electric brake vacuum pump, that you can share?

We have a 2007 CRD LTD and the rear wheel speed sensors needed to be replaced to stop the brake lockups. Even though each of the four wheel sensors were still working within the nominated tolerances, the differences between all four wheels was too much and out of spec. I bought factory...

Hello Carlos I have a 2007 RHD Export KJ Cherokee CRD LTD and am getting the same symptoms with mine. What is the OEM part number of the "booster solenoid" that you replaced? Can you also give me some more information on the "after market small filter" that you used, please? Regards John