Search results

has anyone had an issue of the blower failing to run on any speed when the interior cabin is very cold (below -25c) I've had this issue twice this winter, once it kicked on after driving a kilometer, and more recently it didnt kick on until I went over a decent bump in the road. This also...

Hi folks, after things got a bit colder here im finding my e-brake light coming on somewhat randomly at first it was on when the vehicle was started, more recently now it seems to flash on for a while after releasing the brake, after stopping I've checked for brake fluid leaks and cant see...

anyone able to advise which of these clamps would be for the lower rad hose on a 2006? https://www.mcmaster.com/constant-tension-hose-clamps/constant-tension-spring-band-clamps-for-firm-hose-and-tube/ mopar is telling me a worm gear clamp is correct for my ride, but my current clamps are...

Hi folks, my passenger side rear window has been fallen for a month or two, I've been keeping it up with a wedge of wood inside the door and am finally getting around to fixing it. I assume what failed is the clip thing that I've seen a metal replacement for kicking around this forum. What is...

did a bunch of threads disappear? also anyone find a source for poly steering rack bushings?

Is it safe to use? I think this happened from airing down to much last year, either that or vandalism lol. Pls ignore the rim damage lol, just worries about tire safety, it's a 10 ply mud tire Sent from my SM-N910W8 using Tapatalk

Has anyone tried the 4 inch version of this kit? Any pictures or reviews? Goodridge G-Stop Brake Line Kit (4-15519) Part Number: 4-15519 G-STOP SS Braided Brake Line Kit Includes 2 Front Lines/1 Rear Mid Line/4 in. Extended Lines/Adapters/Banjo Bolts/Washers/Line Locators

Hi Guys Just changed my belt tensioner and now the vehicle won't crank with my key, but command start can still start it. Any advice?

Hey folks, I need to swap out the rear most UCA bushing bolt on passenger side front a arm (previous was torched out and replaced with thinner bolt (without the rotation tab) by a shop) So my major question is what setup would put the least stress on that joint so I can get the current bolt...

Hi guys, Im hunting down a harmonic "thumping" or "thudding" sound on my front passenger side. I've gone as far as re-torquing my UCA upper bolts and pulling my front drive shaft, the thumping seems to happen specifically when im coasting and doesn't seem to happen if the vehicle is leaning...

Has anyone tried a high volume oil pump like this one? Melling M297: Oil Pump 1999-2010 Chrysler 3.7/4.7L V6 Engines | JEGS Thinking about a dual remote filter setup and I would probably need more flow to make it work

Anyone have rivet suggestions for the backing plates? Rebuilt my rear brake and found i need to redo the hardware holding the backing plate, is it possible to rivet it at least partially back without pulling my shafts? Sent from my A0001 using Tapatalk

Hi guys, anyone have wiring color or voltage info for the wiring that goes to o2 sensors? In particular i have to rebuild the wiring loom that goes to my driver side rear o2 sensor, the plug is torn out on both ends so I need to wire new plugs in lol. All the wires seem to be some variation of...

Anyone around wana weigh in on how they like the KJ backbone: how was it for installation? Were you able to rust proof it? How is it holding up after a year or two of use? Other alternatives that don't involve a full size full weight bumper? I plan on installing one this spring when i...

Anyone Remeber if there is an alternate position for fuse 16 to make the rewr aux power only go on with the engine? Currently it's powered always, id like tp change it if possible. I know for some Cherokee there's two fuse positions to change this setting, couldn't find info on KJ for it but i...

Took apart drivers side front end, when i got to removing the bushing bolts for the upper a arm got stuck, tried slamming with a BFH using extensions to push the bolts out, couldn't get them to even budge. I think they're seized to thr bushing, gona take it to a shop i know Monday if i dont hear...

Gona be replacing my driver side front upper control arm this week, ive heard its a pain, any tips or pointers? My understanding is to take weight off that side and unbolt it at ball joint first?

Ive got gear oil on the intermediate shaft housing coming off my front diff on the driver side, any ideas what would cause this?

My upper rad hose seems to have some bubbling /weeping coming from where it seals to the rad. I tried reseating it further up onto the radand that seemed to reduce the leakage alot but im thinking i should just replace it. A while bqck i heard about silicone hoses you can use ect. Anyone have...