Search results

I dont need to kown how to do it, justt looking for some tips to get at the little bugger. Passenger side right behind the motor mount, small hole rotted out. Looks like if i drop the skid plate i have nice access to the motor mount which obviously needs to be removed. But anything else...

Has any one seen any after market fender flares for an early KJ (02-04)? Lost mine a few weeks ago on what was supposed to be a "quick" detour through the woods. long story short i dropped in a hole deep in a puddle and totally f*cked my shit up. You see the aftermarket ones on wranlgers all the...

Hey everyone! Been a while since ive been on, had a lot going on the past few months between school and a new job. Hows every body doing? I feel like im out of the loop haha

Whats goin on guys? Havent been on in while, have had a lot goin on the past few weeks. Any way, is any one going to the swap meet at raceway park in English town this weekend?

Need to get the whole half shaft on the pass side. Should i go with the cheaper re man of a new one?

so after work yesterday i took a drive out to bamber lakes to go wheel my favorite spot. i brought a few contractor trash bags because last time i was out there i could see all the beer cans and other garbage strewn about along the trails, make shift fire pits and lake shore. i got out there and...

This write up is for those of you that need to relocate your fluid bottle due to a smaller bumper or just a replacement for a cracked OE bottle. Things you need: Material: 1.5L coolant overflow bottle $9 at advanced auto or autozone. 16 or18 gauge wire Electrical tape or shrink tubing Sheet...

So i just stopped at harbor freight on my way home from work to do some browsing. As im pulling into a spot i see a kid getting out of a champagne colored kj. Im looking around and picked up a new hobby knife set and proceed to check out where the same kid is on line in front of me. Hes buying...

Haha love it !

Any one know the size bolt for a hub bearing on an 02 sport 4x4? Im pretty sure i got a bad hub when i replaced it last week and the inverted torx bolt on top was a kinda rounded over when i got to it. Wana replace it so i have a good bite when i torque it down after the second replacement tomorrow

Im need of new tires pretty soon and i cant decide on brand and size. I had nitto terra grapplers on my ram but i cant seem to find them in my size. Has any one seen them in 245/70/16 or if 245/75/17 will fit. Im lifted and sit 22" hub to fender at all 4 wheels. I also like the duratracs and the...

Pretty straight forward. Should i trim some fat off the bottom of my front bumper? it would involve deleting the factory fogs and adding bolt ons in its place but i like the more lifted look it gives. Any reason i shouldnt other then personal preference?

Ive seen the term pre-lowered thrown around on the forum and googled it. My search led me to a thread on lost, it said how any kj made after april 2002 is lowered by 3/4" because car and driver flipped one? It got me wondering if my 02 was pre-lowered so i went out and checked the sticker on my...

So i changed my passenger hub bearing on sat. It started off making noise only while turning left and progressed to a constant noise. Once it was changed the hub was silent, until today.... every once in a while while turning left i can here the hub. The odds of me purchasing a bad hub seem...

I know it would take some serious fabrication to fit an in dash unit in a kj, probly have to relocate the climate control console. But has any one gotten one to fit?

After i installed my lift i had to change all the ball joints. I tried best i could to torque the uca bolts but i had to use and extension and im not sure i got full torque because of the extension. Any one have and pointers to get some more room or maybe go at it at a different angle? the...

I dont plan on re gearing, atleast right now any way. But i would like to read up on the procedure if any one has a link to some literature that would be cool. Thanks for assisting in my never ending quest for knowledge haha

so ive seen people making a custom front bumper form a stock wrangler bumper and i was thinking of doin the same. but then i saw this for $100 and figured it would mount with the same mods as a stock bumper. so how much trouble would it actually take to make this work. have access to a welder...

I went to my buddys shop to pick up some cash he owed me. When i got there he was just finishing up changing a steering column on a 02 kj. Along with the money he gave me both cruise control switches off the original steering wheel. How often do these switches go bad?

Figure i might as well star a journal. Better late then never. Out with the old in with the new Before After Up in the air Starting the rear Installed On to the front All finished