Search results

  1. J

    02 Liberty Renegade Limited...Resurrection

    Well I finally got around to getting it back on its feet. Drives well, needs a front wheel bearing. Replaced drivers door lock actuator as it was loud, and passed Germany front door stop as it was broken. Still need to get Hood struts Rear hatch latch and micro switch Change both diffs fluids...
  2. J

    02 Liberty Renegade Limited...Resurrection

    Thanks. It sure saves a bunch of money. These 02 kjs are where it's at...the only easy ones to convert to 4.7, and the only ones with a decent tranny. This one will be getting a jba 3.5" kit and some 31s by winter. Even though the body isn't perfect, $800 for a nice interior and good 3.7 in...
  3. J

    02 Liberty Renegade Limited...Resurrection

    Well, I'm back at it again. The old man needed replacement wheels for his 86 2.1 turbo diesel comanche, so we found a very decent 02 kj with a beautiful sounding motor and junk trans...149k miles for $800. It's limited with pw, pl, power defrost mirrors, heated power leather, cruise...
  4. J

    Jeep Liberty CRD Engine Oil Cooler Torque Specs

    Went with goodntight method.
  5. J

    V8 engine swap

    No, you wouldn't. Not bolt in, no easy way to make any of the computers communicate, thus no way for the gauges to function. Also a violation of federal law to swap an engine that is from any model year older than the vehicle receiving it.
  6. J

    Weathertech floor mats, ventshades, cargo liner

    First paid first served.
  7. J

    How Do I make my alarm working by opening the hood?

    There is no room to put extra wiring through the door harness. Find the color you want for That door switch in the kick panel and splice there.
  8. J

    Repair Ideas?

    It's been said before. Why be nice? You don't need your hand held, you just needed a smack on the back of the head. This site is super laid back, and that was a very placid post by me. Darn liberal "feelings". Take toms advice. Don't bother with a frame shop, just get the...
  9. J

    Repair Ideas?

    Your jeep didn't fail. You and your terrible idea did. Factory tow hooks are for straight pulls only. Did you really think that a lateral pull using the same 3 bolts would work? You needed to tie the two sides together and you would have been fine. As I have said before.
  10. J

    Seeking Advice, Front Pinion

    It's all the same. Bad pinion bearings mean setting preload, setting lash, and likely that your ring and pinion are damaged
  11. J

    Ebay Crossbar thoughts?

    Junk. A friend had similar ones. No weight capacity, no quality in construction. How. Would you feel if your clamp on bars came off on the highway, along with everything on them. I would not want that.
  12. J

    Seeking Advice, Front Pinion

    If you have to ask this question, you need a professional. New bearing will change preload needs, shimming needs, and ultimately require someone who can set gears. So, cheaper would be to replace it all.
  13. J

    Rockrail paint?

    It was sarcasm TJ.
  14. J

    Rockrail paint?

    Should have them line x. I hear they guarantee their work
  15. J

    Rockrail paint?

    I would replace the frame side ones with standard and get used to replacing them.
  16. J

    Rockrail paint?

    Stainless is nt a great idea. It's harder, therefor more brittle. It is equally strong but unlike gr8 and above, it will reach it's stress point and shear
  17. J

    Rockrail paint?

    Por15 takes scrapes and doesn't chip really easily, it is very hard.
  18. J

    Rockrail paint?

    Por15 it then spray your bedliner. No need to clean off any non scale rust...the por converts rust
  19. J

    Please Verify My Potential Setup.

    The change in geometry will eventually wear out the upper ball joints. You may get by without, but you will already have it apart, so why would you want to do it twice
  20. J

    Please Verify My Potential Setup.

    JBA a arms. That will rub without them

Random media

2003 Jeep
photo (2)
after doing donuts in the parking lot at the provincial park
IMG 0444
image
IMG 0893
Pre-lift, showing the added light bar and brush guard.
New tool box. Where stickers belong, had lots of "contingency" stickers on my Chevelle. Took lots of years and a pile of cash to gather all the stic
flex

Latest posts

Staff online

Members online

Total: 520 (members: 4, guests: 516)
Top