Search results
-
Rear upper control arm wont go in all the way
I think I used a chisel in the gap ,a clamp on the arm and axle shaft and rotate the pumpkin for or aft and it dropped right in. Gyro- Gyro
- Post #2
- Forum: KJ General Discussion
-
What size bolts are used to mount the skid plates?
try here https://www.rivetnutusa.com/metric-rivet-nuts/ Gyro- Gyro
- Post #4
- Forum: KJ General Discussion
-
What size bolts are used to mount the skid plates?
4x Bolt M10X1.50X35 and x4 rivnuts are also needed. Gyro- Gyro
- Post #2
- Forum: KJ General Discussion
-
More Information Regarding Kj Renegade Roof foglight mounting
https://www.jeepkj.com/threads/left-windshield-pillar-socket-what%E2%80%99s-it-for.78919/ Check your A pillar,you may have this plug for the roof lights and also check under your dash for the opposite end of this plug. Gyro- Gyro
- Post #4
- Forum: KJ General Discussion
-
Jeep Liberty Brake and Rotor Question
Front flex brake hoses. Gyro- Gyro
- Post #2
- Forum: KJ General Discussion
-
What does Trail Rated add to a 2006 Sport?
And what klc mentioned also.- Gyro
- Post #10
- Forum: KJ General Discussion
-
What does Trail Rated add to a 2006 Sport?
I just googled 2wd Liberty and google pics show no badge on 2wd Liberty's- Gyro
- Post #6
- Forum: KJ General Discussion
-
What does Trail Rated add to a 2006 Sport?
I think trail rated just means it is 4x4. Most other things are trim level upgrades,Limited,Renegade,Rocky Mountain Edition ect. Gyro- Gyro
- Post #3
- Forum: KJ General Discussion
-
4.10 Re-gearing - 2025
When I had mine done about 10 years ago,labour worked out to be about the same as the parts cost. Gyro- Gyro
- Post #3
- Forum: KJ General Discussion
-
I need help identifying a part
My guess would be speed control servo. On 04 and earlier models. 05 and later it is mounted on the inner fender. Gyro- Gyro
- Post #2
- Forum: KJ General Discussion
-
Vehicle sale
First go to the Market Place section,then read the for sale how to and then post in the for sale thread. Gyro- Gyro
- Post #2
- Forum: KJ General Discussion
-
-
Cable through bulkhead (firewall)
Look for where the main harness goes through the firewall from engine bay into the cab. I used a knitting needle to fish it through. Use something with a smooth point so you don't damage any wires. Gyro- Gyro
- Post #2
- Forum: CRD KJ's Section
-
2007 Liberty SIX SPEED backup light switch location
Drivers side of transmission at the rear below the shifter tower.- Gyro
- Post #2
- Forum: KJ General Discussion
-
H&R Spring Review
A 2x4 on edge using the tire as a fulcrum seems to work for most.- Gyro
- Post #105
- Forum: Lift Kit Discussion
-
-
Front suspension noise
First thing to find out is if the bolts were tightened/torqued with the full weight of the vehicle on the ground. Neutral position of the bushings is where they should be torqued. Gyro- Gyro
- Post #2
- Forum: Frequently Asked Questions
-
2009 KK Jeep scalloped driver front tire
Get an alignment too. Gyro- Gyro
- Post #2
- Forum: KK General Discussion
-
How to choose the correct O2 sensors
Jeep KJ likes copper core NGK ZFR 6F-11G gap set at .040. Jeeps have never been famous for good gas milage.:D Gyro- Gyro
- Post #4
- Forum: KJ General Discussion
-
How to choose the correct O2 sensors
That is the correct sensor. It will fit all positions. Have someone with a code reader check for codes, to see which sensor is faulty,no need to replace all sensors. Gyro- Gyro
- Post #2
- Forum: KJ General Discussion
