Search results

  1. ltd02

    Bank 2 misfire

    Might have tweaked a valve seat so it won't close completely. Don't want it to drop completely or you'll really screw things up. This was a common issue on the very early KJs but maybe the bad HG and getting it hot added to the issue in your later 06.
  2. ltd02

    3.7L 02 vs 03 and Later Bedplate and Cylinder Head Bolt Tightening

    I did the bedplate (replaced Crankshaft) and heads (HG replacement) on my departed 02. I followed the 2002 FSM and had no issues. I would recommend doing the same.
  3. ltd02

    Air door blend issues

    You can pull the tubes off the controller knob and hook up a little vacuum pump to force the actuators to work.
  4. ltd02

    Poor heat

    HOAT is a specific chemical makeup of the coolant. Different vehicle manufacturers spec their vehicles with different types of coolant. They determine what works best for their systems. Chrysler has used HOAT for quite a while now. The issue with mixing these different chemicals is that they can...
  5. ltd02

    Poor heat

    Tstat may be stuck open. Sometimes you'll get a code for taking a long time to get up to temp but might not be quite that bad yet. On the good side, way better to run these things cold that to overheat it...
  6. ltd02

    Poor heat

    Yeah that's pretty low. Is it cold where you are? If so it sounds like Tom may have nailed it with the tstat being bad.
  7. ltd02

    I just screwed up the timing.... help.

    Yeah the manual has a pretty good description. The right side has to be physically rotated a few degrees clockwise IIRC to get the V6 mark straight up. There is a special tool to do this that fits on the cam right behind the sprocket and anchors in a little hole but maybe put a socket on that...
  8. ltd02

    Poor heat

    Doubt a couple miles will get it to temp but could depend upon where you are. Sounds cool to me if it were fully up to temp. Mine used to run about 180 to almost 200 depending upon traffic and when fully up to temp. Never checked at the heater hoses.
  9. ltd02

    Poor heat

    Change the temp setting (doesn't matter what directional mode you are in) and listen for a slight buzz behind the center bezel where the switches are located and a bit toward the right side. Might help to remove the glovebox and listen there too. My working blend door actuator motor always made...
  10. ltd02

    What did you do to your jeep today?

    About 9-10" around Frederick MD. They got around 40" in the place I lived before the move down here.
  11. ltd02

    What did you do to your jeep today?

    That offends me... ;)
  12. ltd02

    Forum Stats

    There, You got another one...
  13. ltd02

    What did you do to your jeep today?

    Well that's like getting a real cool thing for Christmas that needs batteries, that you don't have...
  14. ltd02

    Cheap Fix for Transfer Case Cable Bushing/Clip

    My 05 took this bushing: https://smile.amazon.com/gp/product/B01N3Q2NI1/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Not sure when they changed the design but the one you tried first fit my 02.
  15. ltd02

    What did you do to your jeep today?

    Bounce dryer sheets worked for mouse repellant in my area. The MORE scented the better.
  16. ltd02

    Wheel bearing dead

    May be too late for this current issue, but I bought some of that AeroKroil spray penetrating oil. Tom Mudd recommended it often so gave it a try, and it's worked on everything I've tried it on so far. It's pricey but worth it to me since it works. Has been a lifesaver on all the rusted stuck...
  17. ltd02

    Wheel bearing dead

    Can you grind a slot in the nut where it protrudes and use a chisel?
  18. ltd02

    K&N Cold Air Intake

    I've run an AEM brute force CAI (dry cone filter) for 15 years and over 120k in my 4.0L OHV ranger and never had an issue with my engine (187k now). I do run a hydrophobic prefilter and the kit does come with a box setup that draws air from around the headlight and grill, not just sucking hot...
  19. ltd02

    Wheel bearing dead

    Ahh yes, I remember your dilemma. Good luck with that! I hate when those little thing gum up the works.
  20. ltd02

    Wheel bearing dead

    Did you rotate the tires yet?
Top