What did you do to your jeep today?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

sota

Full Access Member
Joined
Apr 6, 2011
Messages
2,324
Reaction score
1,115
Location
NJ
locked down the carry basket.
pulled it out of the garage and put the cover on it to protect it.
kid's car is now in. we're going to get cracking on the suspension work.
so now it'll definitely snow in the next couple of days. :D
 

Btownpreacher

Full Access Member
Joined
Nov 13, 2022
Messages
109
Reaction score
95
Just got my front OME shocks and springs today. Should I replace the upper mounts and isolators at the same time or just reuse the old ones? The lower bushings look worn, and I've heard that if you replace one piece then you should replace all of them. If so, what brand(s) and part numbers should I use? Also, I've heard that the kk lower shock mount forks are taller than the KJ's, so if you replace you KJ forks with kk forks you'll get about an extra inch of ride height. Anyone tried that? Does it work?
 

Deb'nKJ

Full Access Member
Joined
Jun 3, 2022
Messages
527
Reaction score
445
Location
somewhere between London & Zunny Deb'n (England)
It actually stopped down there with you? It's been biblical here. I've been aquaplaning going up hills.
Sorry, because that's about all I achieved in the 2 weeks I had off over Christmas/New Year I've not been very KJ minded of late. Yup, there was that brief respite - but we had floods last weekend!

b-t-w, I've updated that post you quoted from, as rather better progress has been made this weekend.
 

Deb'nKJ

Full Access Member
Joined
Jun 3, 2022
Messages
527
Reaction score
445
Location
somewhere between London & Zunny Deb'n (England)
New front calipers and hoses arrived today, I looked for a 'How to' regarding the hoses but couldn't find anything. Is there anything I need to know before embarking?
'spect you've done the job now but as strange as those flexis look to us, there's nothing peculiar, in principle, to the doing the job. In fact, I replaced a rear caliper on mine (which, incidentally, I'm sure didn't cost anything like £75) without really giving it a thought.

That reminds me, have to go shopping for some pads for mine, as discovered uneven wear on mine, so while those on the left have, probably, 6 months left on them, one of those on the left doesn't :eek:
 

tommudd

Moderator
Staff member
Moderator
Joined
Jul 14, 2005
Messages
22,456
Reaction score
3,642
Location
Southeastern Ohio
Just got my front OME shocks and springs today. Should I replace the upper mounts and isolators at the same time or just reuse the old ones? The lower bushings look worn, and I've heard that if you replace one piece then you should replace all of them. If so, what brand(s) and part numbers should I use? Also, I've heard that the kk lower shock mount forks are taller than the KJ's, so if you replace you KJ forks with kk forks you'll get about an extra inch of ride height. Anyone tried that? Does it work?
3/4 of an inch , but 4 conduit nuts are way cheaper and work the same
 

KJowner

Full Access Member
Joined
Oct 20, 2022
Messages
847
Reaction score
505
Location
Uk
'spect you've done the job now but as strange as those flexis look to us, there's nothing peculiar, in principle, to the doing the job. In fact, I replaced a rear caliper on mine (which, incidentally, I'm sure didn't cost anything like £75) without really giving it a thought.

That reminds me, have to go shopping for some pads for mine, as discovered uneven wear on mine, so while those on the left have, probably, 6 months left on them, one of those on the left doesn't :eek:
You have a dragging brake on that side I would think.
 

Johnny O

Just hangin' out.
Joined
Apr 29, 2021
Messages
2,358
Reaction score
3,164
Location
Bellevue NE
Replaced my rear bumpstops- they were trashed.
Working my way through a checklist of "inspect/repair/replace" in preparation for field season (3 month to go!)

No big desert enduro trip this year, just lots and lots of short ones!
 

lfhoward

Well-Known Member
KJ Supporting Member
Joined
Dec 9, 2012
Messages
2,243
Reaction score
2,425
Location
Philadelphia, PA
Rear CV on the front drive shaft started to self destruct today. I’ve known it needed replacing for a while… but things like brakes took precedence. Now it’s kind of forcing me to deal with it, LOL.

So tomorrow I’m pulling the front drive shaft. I’ll bathe the bolts in penetrating oil ahead of time. On the KK there is an oxygen sensor that blocks driveshaft removal. How much of a PITA are O2 sensors to remove and do you have any tricks and tips?

Edit: I’m looking for ideas that don’t destroy the O2 sensor because it still works and I want to reinstall it.
 

derekj

Full Access Member
Joined
Jul 4, 2013
Messages
194
Reaction score
272
Location
Powell River, BC
Rear CV on the front drive shaft started to self destruct today. I’ve known it needed replacing for a while… but things like brakes took precedence. Now it’s kind of forcing me to deal with it, LOL.

So tomorrow I’m pulling the front drive shaft. I’ll bathe the bolts in penetrating oil ahead of time. On the KK there is an oxygen sensor that blocks driveshaft removal. How much of a PITA are O2 sensors to remove and do you have any tricks and tips?

Edit: I’m looking for ideas that don’t destroy the O2 sensor because it still works and I want to reinstall it.
If you can get a proper O2 sensor socket that really helps and also removing it when the exhaust is hot helps.
 

sota

Full Access Member
Joined
Apr 6, 2011
Messages
2,324
Reaction score
1,115
Location
NJ
Rear CV on the front drive shaft started to self destruct today. I’ve known it needed replacing for a while… but things like brakes took precedence. Now it’s kind of forcing me to deal with it, LOL.

So tomorrow I’m pulling the front drive shaft. I’ll bathe the bolts in penetrating oil ahead of time. On the KK there is an oxygen sensor that blocks driveshaft removal. How much of a PITA are O2 sensors to remove and do you have any tricks and tips?

Edit: I’m looking for ideas that don’t destroy the O2 sensor because it still works and I want to reinstall it.
I'd love to see a picture of this O2 blocking the driveshaft. last time I took mine off I used 2 extensions and deep socket, on my 3/8" ryobi impact. zipped the bolts right off. I had the front end in the air such that I could spin the driveshaft by hand and worked my way around.
 

lfhoward

Well-Known Member
KJ Supporting Member
Joined
Dec 9, 2012
Messages
2,243
Reaction score
2,425
Location
Philadelphia, PA
I'd love to see a picture of this O2 blocking the driveshaft. last time I took mine off I used 2 extensions and deep socket, on my 3/8" ryobi impact. zipped the bolts right off. I had the front end in the air such that I could spin the driveshaft by hand and worked my way around.
I’ll be sure to take some photos. Heading to the parts store for a 7/8” wrench, which I don’t have. I’ll get an O2 sensor socket while I’m there too.
 

lfhoward

Well-Known Member
KJ Supporting Member
Joined
Dec 9, 2012
Messages
2,243
Reaction score
2,425
Location
Philadelphia, PA
Here you go…
You must be registered for see images attach


The offending CV. There is all sorts of lateral play when I grab the drive shaft and shake it.
You must be registered for see images attach


The U joint on the front is fine.
You must be registered for see images attach


The Jeep is developing a few issues I could see while down there today.

A pretty crusty crossmember.
You must be registered for see images attach


A small transmission fluid leak. The pan itself is pretty rusty and will need replacement.
You must be registered for see images attach


Possible rear main seal leak developing? There is a little drip of oil coming from the mating surface of the bellhousing and the engine. (Hard to see in this photo.)
You must be registered for see images attach


Anyhow, all front driveshaft bolts have been zapped with Aerokroil, along with that O2 sensor. Going to the auto parts store now to pick up a 7/8” wrench and an O2 sensor socket for my breaker bar.
 

Rasfetch

Active Member
Joined
Mar 29, 2021
Messages
86
Reaction score
107
Location
Arizona
Decided not to repair or replace the rear differential, I'm just going to keep driving it until it goes out completely. I'll keep saving money that way when it does finally go out, I'll hopefully have enough money to get a nicer car or can just repair the differential at that time.
 

Erskine

Full Access Member
Joined
Aug 2, 2022
Messages
110
Reaction score
142
'spect you've done the job now but as strange as those flexis look to us, there's nothing peculiar, in principle, to the doing the job. In fact, I replaced a rear caliper on mine (which, incidentally, I'm sure didn't cost anything like £75) without really giving it a thought.

That reminds me, have to go shopping for some pads for mine, as discovered uneven wear on mine, so while those on the left have, probably, 6 months left on them, one of those on the left doesn't :eek:
No I haven't. I've bottled it this weekend as after watching a handful of videos the fronts seem a bit of a pig of job (the top hose mount) needing several pairs of hands. Its too cold to be doing this without a heated garage and everyone useful is quite tied up (like me) making every second of daylight count doing farm/horse stuff. Needs to get done though.
 

KJowner

Full Access Member
Joined
Oct 20, 2022
Messages
847
Reaction score
505
Location
Uk
No I haven't. I've bottled it this weekend as after watching a handful of videos the fronts seem a bit of a pig of job (the top hose mount) needing several pairs of hands. Its too cold to be doing this without a heated garage and everyone useful is quite tied up (like me) making every second of daylight count doing farm/horse stuff. Needs to get done though.
I've got the joys of cleaning out a hydraulic system after a pump let go, the filters look like a fab shop bin. A few days before any Jeep stuff happens!
 

duderz7

Full Access Member
Joined
Jan 20, 2016
Messages
1,410
Reaction score
1,134
Location
Weiser, ID
You must be registered for see images attach
You must be registered for see images attach
retorqued and topped up grease on the IRO uca. Also a small brake line drop as well as the wheel speed sensor and diff breather.
 

lfhoward

Well-Known Member
KJ Supporting Member
Joined
Dec 9, 2012
Messages
2,243
Reaction score
2,425
Location
Philadelphia, PA
Tried my hardest to get that O2 sensor out and … well, crap.

The tool. Not a bad quality one either.
You must be registered for see images attach


Outcome = stripped. :rolleyes:
You must be registered for see images attach


Getting help from the professionals now who can torch it off. Running the Jeep to get the exhaust hot is not hot enough. This is no longer a free repair.
 

CherokeeLiberty

Full Access Member
Joined
Nov 14, 2018
Messages
531
Reaction score
734
Location
Northern MN
Tried my hardest to get that O2 sensor out and … well, crap.

The tool. Not a bad quality one either.
You must be registered for see images attach


Outcome = stripped. :rolleyes:
You must be registered for see images attach


Getting help from the professionals now who can torch it off. Running the Jeep to get the exhaust hot is not hot enough. This is no longer a free repair.
Break out the 460’s!

You must be registered for see images attach
 

Latest posts

Members online

Top