Resistance is now LIFTED (plus new MAN tires:)!!!

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

resistance

Full Access Member
Joined
Dec 16, 2009
Messages
156
Reaction score
0
Location
Turkiye
Yes it's finally done.. Had a very hard time finding an international dealer, importing the kit, retrieving at the customs, installation, etc.. But it's over now and I'm deadly tired:) Thanks to Murphyman, Mrneen, Tommudd, Boiler, TBJ, Tony and all the people from Jeepkj and Lostjeeps, who answered all of my questions in endless patience. Thank you. I had definitely NOBODY to provide me the least bit of help here. Without your support, I couldn't have even started doing this.

This is what my 2" lift kit contains:
BDS front and rear coils,
BDS rear shocks,
Rancho RS5764 front shocks
Teraflex front bumpstops (1 missing, so not installed yet..)
Rear bumpstops (rubber mallots)

I've also got new rubber: Cooper Discoverer STT's;) (245/75/16)

Here are the photos(BEFORE/AFTER):
Before:
You must be registered for see images attach

After
You must be registered for see images attach

Before:
You must be registered for see images attach

After:
You must be registered for see images attach

Before:
You must be registered for see images attach

After:
You must be registered for see images attach

Before:
You must be registered for see images attach

After:
You must be registered for see images attach

Before:
You must be registered for see images attach

After:
You must be registered for see images attach


The rear:
You must be registered for see images attach


Front with BDS coils+Rancho shocks:
You must be registered for see images attach

Rear with full BDS:
You must be registered for see images attach


The mechanic said he tried to do the Clevis lift, but could only pry it up about 1 mm. I'm not sure if that is true, or perhaps he didn't try at all though. Is there a noticabe clevis lift (without the conduit nuts) here?
You must be registered for see images attach


I'm not sure how it's measured, but the distance from the wheel center point and fender edge is 51 cm. (20+ inch).What do you think?
 
Last edited:

kj924

Administrator
Joined
Dec 9, 2007
Messages
3,363
Reaction score
1
Location
Prince Edward Island,Canada
Like HJ said, Looks good. Luvin' those Coopers too.

As for the clevis, it looks like about 1 conduit nut gap now, and you still have plenty of room for another 2 nuts of spacing/gap if you want.


Nice Rene
 

Dave

Administrator
KJ Supporting Member
KK Supporting Member
Joined
Feb 22, 2006
Messages
15,567
Reaction score
15
Location
on here
Awesome black lifted renne you got there.

Dave
 

resistance

Full Access Member
Joined
Dec 16, 2009
Messages
156
Reaction score
0
Location
Turkiye
Thank you again for all your help and compliments:) As I've said, I could have NEVER done it without your help. Springs, shocks, bumpstops, clevis, tires, none of them..

This is a bit weird though....the spring shouldn't move that much to the rear....are the BDS rear coils the same size diameter on the bottom as they are on the top? Then they suck. Sorry...

I didn't have a chance to watch the installation (as I'm always working), I saw it when the wheel was taken off, it looked weird. Why is it like that?

BTW, I hear a loud thumping noise from the rear when I go over potholes or high bumps. As a bumpstop, you can see the trimmed and re-shaped rubber mallot below. And the yelow colored "thing" (I don't know what it is called) just above it. Are they too close? Otherwise what would cause that hitting noise? Here is a closer view to it:

You must be registered for see images attach


I also wanted to ask about the amount of lift. I measured from the centre of the rim to the edge of the fender as shown below and it measures a little more than 20". Is this ok for a 2" lift, or is it less than expected?

You must be registered for see images attach
 

resistance

Full Access Member
Joined
Dec 16, 2009
Messages
156
Reaction score
0
Location
Turkiye
Tony, I had to work and I couldn't open the boxes, see the parts and witness the installation process.

Rear shocks are the ones included in the 2" BDS lift kit. If they were too short, then how could they call this a ready made "kit":confused: And the coil ends don't look like the same diameter. You can check them out here:
You must be registered for see images attach


As for the mallets, yes the mechanics invented(!) and applied something more useful(!!!) than I told them :(

The upside down mallets and the weird rear coil position.. Will they do any harm or cause problems??
 
Last edited:

rockymountain

Full Access Member
Joined
Apr 20, 2007
Messages
1,734
Reaction score
27
Location
Spencerville, IN
Looks good Resistance. I would go back and ask them to put the clevis up more. There is 0 (zero) clevis lift there. There is a little catch on the outside of the shock that the clevis should catch on and it is right up there on it. It seems some think that the clevis is supposed to rest on the bottom of the spring perch on the shock. I think you're supposed to use the little "catch". am I right or wrong? From the factory that is how they are, just as pictured and that is also how I did mine. As for the rear springs; are they upside down? it seems the top of the spring isn't centered. The smaller end is supposed to be on the top. Besides it just not being centered is all I can tell from the picture.

Anyway, on the outside it looks great. Those tires really are cool!!
 

ptsb5a

Full Access Member
Joined
Mar 29, 2006
Messages
2,425
Reaction score
20
Location
Northern Alberta, Canada
Well done Resistance, another good looking Black Renengade.

Just to echo what the others have said.... those rear springs don't look right.
 

f1paul

Full Access Member
Joined
Jan 19, 2005
Messages
98
Reaction score
0
Location
T.O.
looks great brother, ive had ome/bilstein lift in my garage for three weeks now, waiting for the time to put it on. making me crazy each time i see one of you guys complete yours and there is no time in sight to install mine. just kidding though, looks sweet, and am really liking how that tire looks also.
 

resistance

Full Access Member
Joined
Dec 16, 2009
Messages
156
Reaction score
0
Location
Turkiye
The long and upside down mallets and the weird rear coil position.. Will they do any harm??
 

resistance

Full Access Member
Joined
Dec 16, 2009
Messages
156
Reaction score
0
Location
Turkiye
I can not get a clear view of the coil and the bumpstops, so I honestly don't know. I only have the picture below, taken while putting the new tires on.

The problem is, I guess the whole thing needs to be taken apart again to correct the rear coil position and shorten the mallets. Given the mechanics skills, this operation unfortunately takes a lot of time and costs a lot around here:( :( :(
You must be registered for see images attach
 

Latest posts

Members online

Top