Recent content by rjkj2005
-
Will 05 doors work on an 07
Yes. 02 through 07 are the same Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #2
- Forum: KJ General Discussion
-
couple questions
There is nothing to mount them to. The bumper is just a plastic cover you would have to add a piece of angle iron to cross support in the picture to make them harder to still. Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #3
- Forum: KJ General Discussion
-
Stock Light Bar or replacement
I got my whole assembly for $75 at a salvage yard. Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #5
- Forum: KJ General Discussion
-
Stock Light Bar or replacement
There are 8 to10 revnuts that hold it on. There are no after market bars that will bolt right up. Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #2
- Forum: KJ General Discussion
-
a better control arm bushing?
Sure. Buy a new set of clevis bushings. Drill out or burn the rubber out of the bushing. Buy some Polyurethane resin. Pour into new bushing housing with center sleeve set in the right location. There Is a company that makes silicone clevis bushings in Australia. But with the cost of...- rjkj2005
- Post #2
- Forum: KJ General Discussion
-
Rear Differential Question..
04 3.7 Chrysler corporate 8.25 differential. With a gear ratio of 3.73 Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #2
- Forum: KJ General Discussion
-
Vibration after 2" suspension installation
The angle of the front drive shaft doesn't change with a lift. Just time for a rebuild of the shaft. Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #2
- Forum: Lift Kit Discussion
-
4.11 gera or 4.10 gears
NO! On the mix and match. 4.10. 4 cylinder KJs came with 4.10 factory. Find one and swap. A whole lot cheaper. Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #2
- Forum: KJ General Discussion
-
overfill 42RLE
A little low is better than a little over. Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #2
- Forum: KJ General Discussion
-
why no clear corners for 05-07?
They didn't sale enough of the 02 thru 04 ones so they never made the for the 05 and up. Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #2
- Forum: KJ General Discussion
-
Suspension knock
Look for rub marks inside the lower control arm mount pockets. If you can see where the rubber bushings have been making Mark's then the lca bushings are bad. If so the lca is moving forward and backwards. This moves the spring into contact with the upper control arm during braking and...- rjkj2005
- Post #4
- Forum: KJ General Discussion
-
new member, need help with Fender fitment
Yes Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #2
- Forum: KJ General Discussion
-
crankcase sensor
Self tapping screws and keep wiggling and pulling. Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #2
- Forum: KJ General Discussion
-
Are JBA UCA's as necessary as Marlin Gehman makes them sound?
Same lift in both pictures. 3.75 inches of lift. These were taken with wheels on the ground. 3 inches is max with factory UCAs. Sent from my SM-G965U using Tapatalk- rjkj2005
- Post #4
- Forum: KJ General Discussion
-
Fender Flares
Yes. But you need 02,03,or 04 flares. 05 and later only the back will fit. Fronts are different do to different front bumpers. Sent from my XT1585 using Tapatalk- rjkj2005
- Post #2
- Forum: KJ General Discussion
