Recent content by jklanier
-
J
No start after crank & cam sensor replacement???
Pulled everything apart, found a broken woodruff key on the crank. used patience, vice grips, pb blaster, and a small flathead to work it loose. used a pick and magnet to get the broken piece out of the crank sprocket. rotated the crank shaft back into alignment with the crank sprocket, poped...- jklanier
- Post #26
- Forum: KJ General Discussion
-
J
Washer pump issue
Hey guys, So, no squirt squirt... Checked fuses. #22 in car, and all the ones under hood. Nothing blown. Its a brand new pump so thats not it. Also tried two different multi-function switches, neither one worked. I used a test light, and it appears no power going to the motor. Im all...- jklanier
- Thread
- Replies: 7
- Forum: KJ General Discussion
-
J
No start after crank & cam sensor replacement???
got everything put back together, jeep sis runing good, thaks for all the help!- jklanier
- Post #24
- Forum: KJ General Discussion
-
J
Broken crank keyway?
got everything put back together Jeep fired up fine, going to be checking the harmonic balancer bolt every day for a while... anything else anyone can think of to be on the lookout for?- jklanier
- Post #11
- Forum: KJ General Discussion
-
J
Broken crank keyway?
Okay, anybody got any tips on getting the key out. im just going at it with various vice grips, pb blaster and patience right now. id thought about a little heat from a torch if i really cant get it...- jklanier
- Post #9
- Forum: KJ General Discussion
-
J
Broken crank keyway?
no idea what caused this, other than a loos balancer bolt... I just replaced the head gasket about 2k miles ago dealership has thee key in stock, heading up there now, and im going to see about a new balancer bolt as well... might as well.. Im hoping theres not valvetrain damage but a...- jklanier
- Post #8
- Forum: KJ General Discussion
-
J
Broken crank keyway?
Thanks for the quick reply! I'm clearly having a super awesome day.... So this is, in theory, fixable. Sweet. Assuming I get the key off successfully, I would need to have someone weld a new key on? Can that be done with the motor in the Jeep? Do I have to pull the timing set? I'm...- jklanier
- Post #3
- Forum: KJ General Discussion
-
J
Broken crank keyway?
SO I finally pulled the timing cover and found this... Any suggestions of how to proceed? Am I completely screwed? :help::sad72:- jklanier
- Thread
- Replies: 10
- Forum: KJ General Discussion
-
J
No start after crank & cam sensor replacement???
SO i Opened up the timing cover and found this.... can this even BE fixed??? Broken Keyway?- jklanier
- Post #22
- Forum: KJ General Discussion
-
J
Timing chain slip?
Yea, I wish, I got the valve covers off, and the notch on the crank is about an inch to the right of tdc when the v6 marks are at 12 o'clock Also my balancr was a bear to get off and back on when I did the head gasket a couple months ago. The AutoZone tool isn't.long enough so I have to go...- jklanier
- Post #10
- Forum: KJ General Discussion
-
J
Timing chain slip?
ok, so the issue for me is that while i can find the tool to remover the balancer, its a lot harder to find the tool to re-install the balancer, plus having just done a head gasket, the timing cover got sealed with RTV soooo thatll be fun too im just whining i know, out to the jeep i go....- jklanier
- Post #8
- Forum: KJ General Discussion
-
J
Timing chain slip?
also, i tried some generic sensors first and when that didnt work i started looking for damaged wires, havent seen any yet but ill look some more bfore i pull the harmonic balancer and the timing cover, as they are a giant PITA.- jklanier
- Post #6
- Forum: KJ General Discussion
-
J
Timing chain slip?
i pulled the battery for probably a half hour or so and played with the sensors back and fourth, buuuutttt, decided to pop the valve covers so i clould check and somehow with both the 'V6' marks at 12 oclock, the notch on the harmonic balancer is about an inch to the right of TDC. hooray...- jklanier
- Post #5
- Forum: KJ General Discussion
