Recent content by jaytango

Thanks Bert. Yes, complete standalone. Electronically, it's just the voltmeter monitoring the voltage of the position sensor, the switch to actuate the TC shift motor, a kill switch that actuates when I shift out of park, and a relay for master power which switches off when the ignition is off...

Hi guys. Just wanted to post the video of my completed 4wd conversion. It was great fun and lots of learning. Hope yall enjoy it. https://www.youtube.com/watch?v=34fdkxh6TNs Parts List: (Phase 1) $200 - Transfer Case $175 - Switch $15 - Volt meter $9 (Phase 2) $340 - Transfer Case Adapter -...

Oh man, thanks! I'm gonna make a run to HD or Lowes and see what I can find. At least I can get everything mounted and running while I continue to look for the stock bolts. I've got the rear-end installed already (trans. extension/shaft, transfer case, & rear driveshaft). I can't record the...

I'm almost done with my 4x4 conversion. I'm only missing the following bolts/nuts and I can't find the part numbers anywhere on any chrysler or mopar sites. Bolt and nut for front axle bracket isolator: https://www.factorychryslerparts.com/productSearch.aspx?searchTerm=52125142AC Bolt and...

Do you have this part? I am currently looking for this exact bracket for my 2010 KK. Do you have this part? Brand new it's too expensive and I haven't had any luck with local junkyards or ebay. Thanks!

I think I found it: 52125450AC, though moparpartsgiant.com shows like it fits the KK 4wd sport on one page but on another it says 'incompatible'.

Does anyone know what the name or part # of this part is? I guess it would be called transmission mount or bracket or something like that? I'm trying to find the one for the 08-12 4wd automatic trans, which has the short transfer case adapter, not the longer 2wd bell. The crossmembers look...

Transfer Case Test Videos I made 2 videos demonstrating how to shift the transfer case and how to detect transfer case position. I hope to document every step of the way. I don't know how long this whole process will take me... maybe 2 months.... maybe 2 years. but anyways. It'll be fun. I love...

I actually did think about that. I'm a web developer and got to play a little bit with an arduino at my last job. Going that route, I could probably use the stock console switch and use like a 555 timer chip to constantly monitor the sensor position pin output and control power, direction and...

I already ordered the mp1522 (coming in today). I wasn't sure how the 231 would bolt on to the KK (plus the different shaft flanges) so I went with the stock TC. I'm gonna start designing the homemade switching circuit using a DPDT and a meter to give me a position based on the 5v feedback. If...

Does anyone know what's the stock ratio for the KK 2WD rear differential? I'm shopping for parts and a guy who has the front end asked me which ratio do I need. I'm assuming it has to match my rear diff ratio?

I was thinking about that but the 2WD has a longer extension housing on the transmission, whereas the 4WD has a short housing (and inner intermediate shaft). I was wondering if(short_housing.length + transfer_case.length = long_housing.length).

Does anyone know if they are the same length or different? Maybe I can get a volunteer to go out with a tape measure and get a quick reading from flange to flange on the 4WD so I can compare to my 2WD. I checked on the mopar site and there were 4 different shafts. 3 said 4WD, one says 2WD. If...

I probably won't do it but I was curious about converting my 2WD KK to 4WD. From what I understand, the KK uses the MP3022 (Selectrac II) or MP1522 (Command-trac II) transfer case which, are electronically controlled. I've been researching the controls of the TC and on one service site it says...

Finally found it! I finally found it, thanks to this thread: https://www.nitroforumz.com/threads/a-c-leaking-water-under-the-carpet.41454/ Here is a pic of the drain: https://i.imgur.com/NqFNb5V.jpg And here is a video of where I cut out the head shield to find it...