Recent content by GnomeKing
-
Camshaft Position Sensor
I replaced both with NTK, no difference- GnomeKing
- Post #5
- Forum: KJ General Discussion
-
2005 KJ Liberty - Service Manual v2025-03-09
Official service manual for KJ - 2005- GnomeKing
- Resource
- 2005 book manual service manual
- Category: Example category
-
07 liberty turn signals and flashers quit working
When I was researching LED bulbs for turn signals, the conclusion was that you have to use resistors, because relays for turn signals are not replaceable as they are part of the emergency flashers module, so ya I think everything related to turn signals/ flashers is in there, not separate relays.- GnomeKing
- Post #4
- Forum: Introductions
-
07 liberty turn signals and flashers quit working
AFAIK the flashers don’t have its own separated module, it’s all integrated in hazard light switch at the center of the console https://www.rockauto.com/en/catalog/jeep,2007,liberty,3.7l+v6,1433762,electrical-switch+&+relay,hazard+warning+switch,4468- GnomeKing
- Post #2
- Forum: Introductions
-
-
Sensor issues
I mean, it runs without issues most of the time- I’m getting P0344 either right after start or within first couple of minutes of driving, clear it and the. I can drive for hours without issue OR on heavy/fully throttle acceleration. I have ordered new connector pigtail bc old one was soaked with...- GnomeKing
- Post #7
- Forum: KJ General Discussion
-
2002 Jeep Liberty coolant bleeding nut rusted shut
I was able to get mine out after soaking it with PB Blaster and gentle tightening/loosening. I put a bit antiseize on it afterwards. I’m not convinced tho it’s the best for place for bleeding the system- it sits well below the reservoir, so coolant comes out of it very early. I bled the system...- GnomeKing
- Post #2
- Forum: KJ General Discussion
-
Manifold Absolute Pressure Sensor Connector
Rockauto has pigtails too https://www.rockauto.com/en/catalog/jeep,2005,liberty,3.7l+v6,1430900,electrical-connector,manifold+pressure+(map)+sensor+connector,2597- GnomeKing
- Post #6
- Forum: KJ General Discussion
-
Sensor issues
@Cbach Did you have the code coming back? I tried bunch of aftermarket sensors without success. https://www.jeepkj.com/threads/camshaft-position-sensor.80380/post-816335- GnomeKing
- Post #5
- Forum: KJ General Discussion
-
Camshaft Position Sensor
@dirtbagjack What brand of CPS sensor did you use? I replaced (and unfortunately prematurely threw away) the original camshaft position sensor, and now I’m getting P0344 (Camshaft Position Sensor “A” Circuit Intermittent (Bank 1)) randomly, putting the engine into limp mode, until I clear the...- GnomeKing
- Post #3
- Forum: KJ General Discussion
-
hub bearing bolt size?
@albrandwood thanks for pointing out the torque-spec! I didn't check how the bolts are stamped, and only needed to replace on of them, so probably not too critical, but yeah, I'm gonna replace the Amazon one with the one from eBay - https://www.ebay.ca/itm/235400094399 - seems much higher...- GnomeKing
- Post #6
- Forum: KJ General Discussion
-
What is this hose - 34611-B - going into the airbox?
For anyone looking for genuine replacement, I was able to get both tubings via my local Chrysler dealer: - https://store.mopar.ca/oem-parts/mopar-cylinder-head-to-air-cleaner-hose-53013723ac - https://store.mopar.ca/oem-parts/mopar-crankcase-vent-to-intake-manifold-tube-53031133ae Part numbers...- GnomeKing
- Post #9
- Forum: KJ General Discussion
-
Coil 6 Insufficient Ionization, Multiple Cylinder Misfire, Fuel Injector 4 Circut/Open
In my case (Coil 4) Low Ionization was caused by fault ECM/PCM - replaced with refurbished one from Flashmasters - after ruling out spark plugs, ignition coils, injectors and wiring continuity...- GnomeKing
- Post #23
- Forum: KJ General Discussion
-
hub bearing bolt size?
So, the bolt from Amazon (https://www.amazon.ca/dp/B0D2BKXCD7) worked without any issues. There’s plenty of space for the socket, at least when installing with steering knuckle out, and I don’t see any issue with extra 2mm of length. (I replaced only one bolt that had stripped head for now.)...- GnomeKing
- Post #4
- Forum: KJ General Discussion
-
hub bearing bolt size?
For anyone replacing the bolts - this is the original bolt: - https://www.idparts.com/knuckle-bearing-bolt-liberty-crd-06503088-p-10027.html - https://www.summitracing.com/parts/mop-06503088 -...- GnomeKing
- Post #3
- Forum: KJ General Discussion
