Recent content by CTJEEP

  1. C

    Bt4 or isb 4. Cummins diesel

    Owning a KJ , and a 4BTA, it would appear near impossible to fit the engine under the hood for vertical clearance issues. A 4BT is near 3' tall......major issue in a GM square body. The lack of a full frame makes the conversation more challenging & costly. If you have enough money, to make...
  2. C

    Roof lights vs sun roof

    Not a big fan of sun roofs ..... have sealed them shut with Lexol clear sealant.... If mine was steel, I would glue it solid with epoxy or SEM Structual adhesives & grind it smooth....plastic edges & paint the whole roof...never to see it again.
  3. C

    Brake bleeding

    Bought SPEEDI - BLEED ... out of Canada... works great. Try. Hi - Lo Distributors, BC, Canada.
  4. C

    Brake bleeding

    Brake fluid is cheap.... Dirty / Contaminated fluid is not your friend... that's why your doing calipers. . . Use a Power Bleeder to push fluid through the Master Cylinder , ABS system, to remove air, contaminated old fluids etc out of the lines + calipers. Bleeding an ABS system can be...
  5. C

    Inner Rocker Panels

    After market rockers are short on top + don't connect at the vertical pinch weld. The inner rocker panels are sandwiched into the outer rocker + inner floor assembly. along with the connection of the Center pillar creating clearance issues. What I've found are few KJ's with perfect rockers...
  6. C

    Replacement Seat bottom cushions and seat cover source

    Local U-Dissambe yard always has Liberties with interiors... Disassembly is a pia.... but starting with a passenger seat - it would be a low mileage part.
  7. C

    2005 KJ Bumper Patterns

    Has anyone built a front bumper for a 2005 - 2007 KJ , and made actual patterns, or prints with dimensions? Don't want to.reinvent the wheel. . .
  8. C

    Re-painting Front Grill Insert

    KRYLON for plastic is a great product, if you can still find it.... Like the SEM, but it starts over $50 quart + calls for adhesion promoter.. more $$$$$
  9. C

    About to buy Jeep Liberty 2007 Limited 2/4wd...need advice on what to check when I see it

    Weak link on the tin is bottoms of doors rotting, and rear section of rocker plugging up with silt + salt ... Rear section of rocker + inner rocker get eaten up... Plastic shields hide the real condition. Probe behind the plastic with an Ice Pick... if it's soft, move on. Tom Mudd is...
  10. C

    Brand new Front Bumper Jeep KK

    Is this bumper still available?
  11. C

    06 Liberty Diesel Idler Pulley

    Taken off the Box Nachi 46 x 17 210603 6203 - 2NSE9C3* **** cut yours apart . . .check dimensions. - bearings may be different from one vendor to the next
  12. C

    06 Liberty Diesel Idler Pulley

    I cheated....I put the OEM pulley in the lathe.... turned the rivet heads down... Put in NACHI bearings in the steel housings. Reassembled the unit with small allen head bolts. I trust Nachi, more than the generic bearings in cheap parts.
  13. C

    Dark Grey Fender/Bumper Color Code?

    Codes probably exist. But there are almost NO products still on the market, specifically ment for automotive soft rubbery parts. There used to be lots of colors made for refinishing.plastic parts with the color molded in. VOC compliance has taken alot of automotive paint products off the...
  14. C

    DIY Front Bumper

    Unfortunately, the above bumper was custom built on Poland. They wanted the Jeep in their shop to make a bumper. Sad .... one less choice.
  15. C

    KJ Winch Bumper - MOVE

    They make kits to assemble in your garage.. much less money than ARB

Latest posts

Members online

Top