Im back, well kinda. still with the same silver jeep that i had before. its been about a year since ive been on the site. I blew a bearing in my jeep and its been sitting for over a year. i bought a rolled jeep from a member on here for an amazing price! I proceeded to do the worlds slowest...
so i have this 03 shell with disc brakes and my 02 has drum. has anyone ever converted their drums to discs? or know if its possible, and if so what would i have to do
Its been about 95 - 100 degrees here in good ole MN with index of about 105 - 110. My jeep has been soild to me but in this heat it has been over heating. always overheats if the ac is on full blast but on some of these hot days on long return trips it wiil over heat if the ac is on at all and...
I almost got t-boned a couple weeks ago, and i hit a curb at 20ish mph trying to not get killed. I drove it home with the alignment way out of whack. the passenger side tire was really turned in. I cant see any damage anywhere so i adjusted the passenger tie rod until the tires were at least...
2 years ago my brother gave me a set of BFG ATs for Xmas, they were used and had some interesting wear but they still had a bunch of tread so i was very happy for the tires. After 2 years of use and 20k miles the ATs were DEAD. Even in the lightest rain they were rather scary at this point! So...
So im set that im going with treadwright brand tires, but im having trouble deciding between the 'Warden A/T' or the 'Guard Dog M/T'. Im taking off a bald set of BFG A/Ts which are pretty much the same as the Wardens. Im not sure if it was how bald they were or what but my BFGs were terrible in...
FS:02 03 Jet Stage 2 chip for KJs
Have this laying around and i figure it can go toward some tires for my ladyfriend. Lets start the bidding at $100shipped obo
*pics coming tonight
can any one send me a pic asap of a sway bar endlink installed properly. it will fit either way but i want to know which is the right way 100%. thanks i know this is simple but i just want to know for sure when i toss in the new ones in case my old one were put in wrong (i went through some end...
If your driveshaft boot looks like this its time to replace the head or get a new driveshaft, replacing the head is only 1/3 the cost so why not just do that.
first step is to hit up eric at automotivepartsunlimited.com and get your new head or driveshaft
Remove the 6, 8mm bolt on...
So tonight i had a 2 hour drive in a Crazy thunderstorm. I noticed while driving my coolant guage would drop, sometimes all the way to cold and then go half way and back usually staying at half way. as i was about 2 miles from my house i feel my revs changing, it would drop then go high thengo...
1 - - So my front sway bar will be the death of me. i put up with the sway bushing making noise until i spray them with white lithium grease, but that only last about 1000 miles then i got to spray them again. I am back to using greased stock bushings. They dont look like bad shape but only 1000...
so of course now that im back from my trip and fixing all the small things i wore out, the check engine light just came on. I get p0837 transfer case position switch, and p0442 small emissions leak.
-ive heard the transfer case sensor is very common but so far ive had no errors in the 4wd...
Ive been real big into photography and state/national parks. I decided it was time to take a trip to see a good number of them. So i set aside 8 days to go see 5 national parks, (rocky mountain, teton, yellowstone, wind cave, and badlands) and a few state parks. my kj had 133k miles on her when...
I am about to go on a 3500 mile 5 national park tour. I would like to save some money by using my stock tires and wheel rather then my cragars and bfgs. but after an alignment and tossing them on the a arm is close to the rubber. it isnt touching but its only 1/4 inch away. not that it matters...
This write up is on how to install any A-arms into a Liberty. I am using JBA gen3 but there are many out there. This will also work for stock arms.
Put your Liberty on jackstands and take off your front tires
time to go
undo the upper ball joint and break it lose, i like to leave the jack a...
-First things first you will need your new axle. Napa is your best bet. good axles with a lifetime warranty. The core charge on the axle is pretty hefty but you will get your money back later
-Second you will need a axle nut socket. I wouldnt spend any money on one unless your really really...
Ive had my Liberty for 5 years and ive never seen a modified Liberty in person. . . . . . until today. Damn nice renegade. So who was visiting Rochester
Im picking up a axle in the morning , waht do i need to know in pulling out and installing the new one. is there any clips holding the old one in? do i have to drain anything? anything else i should know.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.